Car raised on the ramp for underbody inspection at KITH Cars Garage & Bodyworks, Hackbridge

Rust Repairs and Welding for Mitcham Cars, 8 Minutes Away

Family estates and people carriers that have done years of school runs are some of the cars we weld most often, and Mitcham has plenty of them. Our workshop is about 8 minutes from Mitcham, straight down Cranmer Road and Carshalton Road.

  • ~8 min from Mitcham
  • Mon–Fri 8am–8pm · Sat 8am–5pm
Loading instant quote…

Why structural rust matters on the fast A236 across Mitcham Common

Across Mitcham Common the A236 feels open and fast, and speeds creep up between the junctions. It's a good reminder of what a car's body shell is for. On a modern monocoque car the sills, floor and crossmembers carry the load of the whole car and are designed to protect you in a collision. When those parts have rusted thin, the car can drive perfectly normally day to day while being far weaker than it was designed to be.

That's why the MOT is strict about corrosion near suspension, steering and seat belt mountings. People carriers and larger estates, common on the terraces around Lavender Fields and the town centre, carry heavy loads and are often kept for many years, so their rear arches, rear floor and sills are where we find most trouble. Seat belt anchor points in the rear floor are worth checking on any older family car. Floors under the boot can also rust where a leaking tailgate seal has let water sit in the spare wheel well.

When a Mitcham car comes in, we inspect it on the ramp, probe the suspect areas and separate structural rust from cosmetic. We cut out corrosion back to sound metal, form or fit a new section and weld it in, seam welding where the structure needs it. Then it's sealed, primed, underbody coated and treated with cavity wax. We'll also mention anything nearby that's likely to cause a problem at the next MOT, so there are no surprises later on.

Being so close helps. You can drop the car off on the way to Mitcham Junction station and, for a smaller repair, often pick it up the same evening. You'll get a written quote first, a call if the rust proves worse once cut into, and our 12-month workmanship warranty on the work. If the car has a dangerous defect, we can collect it from Mitcham instead.

Welding & Rust Repair: what’s involved

Most cars have a monocoque body, meaning the shell itself acts as the chassis. Sills, floor pans, crossmembers and the areas around suspension and seat belt mountings carry load, so rust there weakens the car. Corrosion usually starts where water and road salt collect: inside sills, behind arch liners, along seams and around jacking points, and it often works from the inside out.

The MOT treats corrosion seriously. Excessive corrosion in load-bearing structure is a failure, particularly within 30cm of prescribed areas such as suspension, steering and seat belt mounting points. A proper repair means cutting back to sound metal, fitting a new steel section and welding it in, then sealing and protecting it inside and out. Covering rust with filler or a plate over rotten metal doesn't fix it, and a tester can fail an inadequate repair on a structural area.

From £80Written quote first
2 hours – 3 daysTypical time in the workshop
3 monthsWorkmanship warranty

Signs of rust that needs welding

Bubbling paint on sills or arches

Rust forming underneath the paint. It's usually more extensive than the visible bubbles suggest.

Holes or flaking metal underneath

Floor pans, sills, jacking points and crossmembers that flake or can be pushed through with a probe.

MOT advisory or failure for corrosion

An advisory is a warning worth acting on; a failure for structural corrosion must be repaired before the car can pass.

Soft or crumbling jacking points

If the sill crushes or the jack sinks into it, the structure around it is weakened.

Rust around suspension mountings

Corrosion near spring seats, strut tops, subframe or trailing arm mounts is structural and needs prompt repair.

Water in the footwells

Can be caused by holes in the floor, although blocked drains and door seals are more common causes, so we check.

Rust on door bottoms and boot floor

Often cosmetic rather than structural, but cheapest to repair while the rusted area is still small.

When should it be done?

Deal with structural rust as soon as it's found, ideally before the MOT so you have time to plan. Corrosion advisories are worth acting on, because another winter of salted roads can turn an advisory into a failure needing bigger repairs. Cosmetic rust on door bottoms or arch edges isn't a safety issue, but it's cheapest to fix while it's still at the bubbling stage. Older and classic cars benefit from a regular underside inspection.

  • MOT advisory mentioning corrosion: before the next winter or MOT
  • MOT failure for corrosion: before retest, and before driving at all if the defect was rated dangerous
  • Bubbling paint on sills, arches or door bottoms: while the rust is still small
  • Buying an older or classic car: underside inspection before or soon after purchase

How we repair rust and welding

  1. Inspection on the rampWe examine the underside, probe suspect areas and read any MOT failure sheet, separating structural corrosion from cosmetic.
  2. Written quoteWe explain what's structural, what's cosmetic and what should be prioritised. Rust sometimes proves more extensive once cut into, and we'll contact you before doing anything extra.
  3. Access and protectionTrim, arch liners, seats or carpets are removed as needed, and fuel lines, brake pipes and wiring are protected or moved away from heat.
  4. Cut out corrosionRusted metal is cut back until we reach clean, sound steel.
  5. Fabricate or fit repair sectionsNew steel sections are formed in the workshop, or pre-formed repair panels are used where available and a good fit.
  6. Weld inThe new metal is MIG welded in, seam welded where the structure requires it, and the welds are dressed back.
  7. Seal and protectJoints are seam sealed and primed, the underside is coated with underbody protection and enclosed sections are treated with cavity wax.
  8. Refit, check and hand overEverything is refitted, pipes and wiring are checked, and we explain what was repaired and anything else worth watching.

Steel and materials

Repairs are made with new steel of a suitable thickness for the area, either fabricated in the workshop or using pre-formed repair panels where they're available and fit well. After welding, joints are sealed, primed and protected with underbody coating, and enclosed sections such as sills are treated with cavity wax, which creeps into seams to slow future corrosion from the inside.

  • New steel sheet of the appropriate thickness
  • Pre-formed sill and arch repair panels where suitable
  • Weld-through primer and anti-corrosion primer
  • Seam sealer
  • Underbody protection and cavity wax

How long it takes

2 hours – 3 days

A single small MOT repair can often be done in 2–4 hours. Sills, floor sections or several areas can take 1–3 days, and extensive work on older cars longer. If the rust turns out to be worse once cut out, we'll call you before going further.

What’s included

  • Underside inspection and written quote
  • Cutting out corrosion back to sound metal
  • New steel welded in
  • Seam sealing, priming and underbody protection on the repair
  • Cavity wax in enclosed sections that have been repaired
  • 12-month workmanship warranty

From Mitcham to our Hackbridge workshop

From the town centre, follow the A217 London Road south to the Cricket Green, then take Cranmer Road (A239) to join Carshalton Road (A237) heading south. Carshalton Road crosses the railway and tram lines beside Mitcham Junction station and, past Beddington Corner, becomes London Road into Hackbridge, where Soho Mills is on London Road near Hackbridge station.

Follow London Road to the Cricket Green, take Cranmer Road (A239) onto Carshalton Road (A237) past Mitcham Junction station and on into Hackbridge, around 8 minutes. If the car shouldn't be driven, we can collect it.

Directions from Mitcham

About Mitcham

Mitcham is a largely residential suburb in the east of Merton that grew from an old Surrey village famous for lavender growing, which still features on Merton Council's coat of arms. Its historic core is a string of village greens, from Fair Green and the clock tower in the town centre to the Cricket Green, with the wide open space of Mitcham Common to the south-east. Housing ranges from Victorian and interwar terraces to large council estates such as Phipps Bridge and Pollards Hill. Driving here means a mix of busy A-roads funnelling traffic between Tooting, Streatham, Morden and Croydon, and quiet residential side streets lined with parked cars.

Places nearby: Mitcham Common, Mitcham Cricket Green, Mitcham Clock Tower, Eagle House, The Canons, Church of St Peter and St Paul

Postcodes: CR4 · London Borough of Merton

More about KITH for Mitcham drivers

Welding & Rust Repair in Mitcham: your questions answered

Can I drop my car off on the way to Mitcham Junction station?

Yes, the workshop is on the same road a few minutes south, and Hackbridge station is next door too. Smaller repairs are often done the same day. We'll call you with the quote before starting.

The MOT mentions rust near a seat belt mounting. Is that serious?

Yes, it's treated as structural because the mounting has to hold in a crash. Corrosion within the prescribed area around it can fail the MOT. We cut the rust out and weld in new steel so the mounting is sound again.

Is my old people carrier worth welding?

If it runs well and the rust is limited, often yes, as replacing a seven-seater is expensive. We'll look at the whole underside and tell you if the corrosion is too widespread to be worth it.

Will my car pass the MOT after welding?

We repair the items on your failure sheet to a standard that meets the MOT inspection requirements, although the tester makes the final decision at the retest. If we find other corrosion nearby that's likely to cause a problem, we'll point it out before the retest.

Is it worth welding an older car?

It depends on how much rust there is and what the car is worth. A couple of sill repairs on an otherwise sound car are usually worthwhile. Widespread corrosion across floors, sills and mountings can cost more than the car is worth, and we'll give you an honest view.

Can you just patch over the rust?

Not on structural areas. Welding a plate over rotten metal traps moisture so the rust carries on underneath, and a tester can fail it as an inadequate repair. We cut out to sound metal and weld in new steel.

What's the difference between structural and cosmetic rust?

Structural rust affects load-bearing parts such as sills, floors, crossmembers, chassis legs and the areas around suspension and seat belt mountings. Cosmetic rust is on outer panels like door skins and bolt-on wings, which aren't load-bearing and usually only fail an MOT if they leave sharp edges.

How can I slow down rust?

Rinse the underside during winter to remove road salt, keep door and sill drain holes clear, and deal with stone chips early. On older cars, cavity wax in the sills and underbody protection make a real difference, and we can apply them.

Price your welding and rust repair now

Enter your reg and we’ll look up your car and price the job from our own labour rates and the book time for your model. Then book it in with a fixed written quote before any work starts.

  • Free, about 30 seconds, no sign-up
  • Parts, labour and VAT included
  • 12-month workmanship warranty
  • Collection from Mitcham can be arranged
“It’s rare to find a garage you can truly trust. Fair price, brilliant customer service.”Thinushan K. · ★★★★★ Google

Prefer to talk? Call 020 4629 9469 or WhatsApp us.

Chat on WhatsApp