Car raised on the ramp for underbody inspection at KITH Cars Garage & Bodyworks, Hackbridge

Welding and Rust Repair for Beddington Drivers

An older car that already meets ULEZ standards is worth keeping, and rotten sills are often the only thing stopping it passing an MOT. From Beddington our Hackbridge workshop is about 6 minutes away, and we cut out the corrosion and weld in new steel rather than covering it up.

  • ~6 min from Beddington
  • Mon–Fri 8am–8pm · Sat 8am–5pm
Loading instant quote…

Keeping a ULEZ-compliant Beddington car legal for longer

Since the ULEZ expansion in August 2023 took in Beddington, plenty of households have realised that the compliant petrol hatchback or Euro 6 diesel on the drive is worth more to them than its book value suggests. Replacing it means finding another compliant car. Welding in a new sill section or a patch of floor is usually far cheaper, and on a car with a healthy engine it can add years of use. We'll tell you plainly if the rest of the car justifies the repair, because sometimes it doesn't.

The vans and pickups that work out of the Beddington Lane industrial estates have their own pattern. They spend long days on roads carrying grit and dirt from recycling and waste sites, and mud packs into the rear arches and around the spring hangers, where it holds moisture against the steel. Commercial bodies also tend to rust along the floor edges and at the rear crossmember. We put the van on the ramp, probe the suspect areas and tell you which repairs are structural and which can wait.

Family cars around the residential streets off Plough Lane and towards Wallington mostly show rust at the sills, the jacking points and the rear arch lips, the places road salt and water sit through winter. Cars kept near BedZED and the Beddington Lane tram stop that rarely leave the kerb can suffer too, because a car that stays damp underneath never really dries out. If your last MOT listed corrosion as an advisory, the months before the next test are the right time to deal with it.

Every job starts with a written quote that separates structural work from cosmetic. If the metal proves worse once we've cut into it, we phone before going further. Repairs are sealed, primed, underbody coated and cavity waxed where the section is enclosed, and they carry our 12-month workmanship warranty. Most small repairs are finished the same day.

Welding & Rust Repair: what’s involved

Most cars have a monocoque body, meaning the shell itself acts as the chassis. Sills, floor pans, crossmembers and the areas around suspension and seat belt mountings carry load, so rust there weakens the car. Corrosion usually starts where water and road salt collect: inside sills, behind arch liners, along seams and around jacking points, and it often works from the inside out.

The MOT treats corrosion seriously. Excessive corrosion in load-bearing structure is a failure, particularly within 30cm of prescribed areas such as suspension, steering and seat belt mounting points. A proper repair means cutting back to sound metal, fitting a new steel section and welding it in, then sealing and protecting it inside and out. Covering rust with filler or a plate over rotten metal doesn't fix it, and a tester can fail an inadequate repair on a structural area.

From £80Written quote first
2 hours – 3 daysTypical time in the workshop
3 monthsWorkmanship warranty

Signs of rust that needs welding

Bubbling paint on sills or arches

Rust forming underneath the paint. It's usually more extensive than the visible bubbles suggest.

Holes or flaking metal underneath

Floor pans, sills, jacking points and crossmembers that flake or can be pushed through with a probe.

MOT advisory or failure for corrosion

An advisory is a warning worth acting on; a failure for structural corrosion must be repaired before the car can pass.

Soft or crumbling jacking points

If the sill crushes or the jack sinks into it, the structure around it is weakened.

Rust around suspension mountings

Corrosion near spring seats, strut tops, subframe or trailing arm mounts is structural and needs prompt repair.

Water in the footwells

Can be caused by holes in the floor, although blocked drains and door seals are more common causes, so we check.

Rust on door bottoms and boot floor

Often cosmetic rather than structural, but cheapest to repair while the rusted area is still small.

When should it be done?

Deal with structural rust as soon as it's found, ideally before the MOT so you have time to plan. Corrosion advisories are worth acting on, because another winter of salted roads can turn an advisory into a failure needing bigger repairs. Cosmetic rust on door bottoms or arch edges isn't a safety issue, but it's cheapest to fix while it's still at the bubbling stage. Older and classic cars benefit from a regular underside inspection.

  • MOT advisory mentioning corrosion: before the next winter or MOT
  • MOT failure for corrosion: before retest, and before driving at all if the defect was rated dangerous
  • Bubbling paint on sills, arches or door bottoms: while the rust is still small
  • Buying an older or classic car: underside inspection before or soon after purchase

How we repair rust and welding

  1. Inspection on the rampWe examine the underside, probe suspect areas and read any MOT failure sheet, separating structural corrosion from cosmetic.
  2. Written quoteWe explain what's structural, what's cosmetic and what should be prioritised. Rust sometimes proves more extensive once cut into, and we'll contact you before doing anything extra.
  3. Access and protectionTrim, arch liners, seats or carpets are removed as needed, and fuel lines, brake pipes and wiring are protected or moved away from heat.
  4. Cut out corrosionRusted metal is cut back until we reach clean, sound steel.
  5. Fabricate or fit repair sectionsNew steel sections are formed in the workshop, or pre-formed repair panels are used where available and a good fit.
  6. Weld inThe new metal is MIG welded in, seam welded where the structure requires it, and the welds are dressed back.
  7. Seal and protectJoints are seam sealed and primed, the underside is coated with underbody protection and enclosed sections are treated with cavity wax.
  8. Refit, check and hand overEverything is refitted, pipes and wiring are checked, and we explain what was repaired and anything else worth watching.

Steel and materials

Repairs are made with new steel of a suitable thickness for the area, either fabricated in the workshop or using pre-formed repair panels where they're available and fit well. After welding, joints are sealed, primed and protected with underbody coating, and enclosed sections such as sills are treated with cavity wax, which creeps into seams to slow future corrosion from the inside.

  • New steel sheet of the appropriate thickness
  • Pre-formed sill and arch repair panels where suitable
  • Weld-through primer and anti-corrosion primer
  • Seam sealer
  • Underbody protection and cavity wax

How long it takes

2 hours – 3 days

A single small MOT repair can often be done in 2–4 hours. Sills, floor sections or several areas can take 1–3 days, and extensive work on older cars longer. If the rust turns out to be worse once cut out, we'll call you before going further.

What’s included

  • Underside inspection and written quote
  • Cutting out corrosion back to sound metal
  • New steel welded in
  • Seam sealing, priming and underbody protection on the repair
  • Cavity wax in enclosed sections that have been repaired
  • 12-month workmanship warranty

From Beddington to our Hackbridge workshop

From Beddington village, take Church Road to Croydon Road (A232) and head west towards Wallington. At Wallington Green, turn right onto London Road (A237) and follow it north to Soho Mills in Hackbridge.

Take Church Road to the A232 Croydon Road, head west to Wallington Green and turn right up London Road (A237) to Soho Mills, around 6 minutes. If the MOT rated a corrosion defect as dangerous, don't drive it; we can collect it from Beddington.

Directions from Beddington

About Beddington

Beddington sits in the north-east corner of the London Borough of Sutton, between Wallington, Hackbridge and the Croydon boundary. Around the historic village are Beddington Park, Carew Manor and St Mary's Church, with interwar and postwar housing in the residential streets. To the north, Beddington Lane is lined with industrial estates, waste and recycling sites and the sewage works, so the roads there carry lots of lorries and vans. It mixes quiet family suburb with a working industrial area.

Places nearby: Beddington Park, Carew Manor, Carew Manor dovecote, St Mary's Church, Beddington, Beddington Energy Recovery Facility, Beddington Farmlands

Postcodes: SM6, CR0 · London Borough of Sutton

More about KITH for Beddington drivers

Welding & Rust Repair in Beddington: your questions answered

My car is ULEZ compliant but failed on rusty sills. Is it worth welding?

Often, yes. If the engine and gearbox are sound and the rust is limited to the sills or a section of floor, welding usually costs far less than buying another compliant car. We'll look at the whole underside first and tell you honestly if it's more widespread than it looks.

Can you weld the floor and crossmember on a works van?

Yes. Vans are welded in the same way as cars, cutting back to sound metal and letting in new steel of a suitable thickness. We'll check spring hangers and load floor edges too, as they commonly rust on vans used on dusty industrial roads.

Can I leave the car and walk home to Beddington?

Yes, the walk back along London Road and through Beddington Park isn't long. Hackbridge station is also next to the workshop. For longer welding jobs we can arrange collection and delivery instead.

Will my car pass the MOT after welding?

We repair the items on your failure sheet to a standard that meets the MOT inspection requirements, although the tester makes the final decision at the retest. If we find other corrosion nearby that's likely to cause a problem, we'll point it out before the retest.

Is it worth welding an older car?

It depends on how much rust there is and what the car is worth. A couple of sill repairs on an otherwise sound car are usually worthwhile. Widespread corrosion across floors, sills and mountings can cost more than the car is worth, and we'll give you an honest view.

Can you just patch over the rust?

Not on structural areas. Welding a plate over rotten metal traps moisture so the rust carries on underneath, and a tester can fail it as an inadequate repair. We cut out to sound metal and weld in new steel.

What's the difference between structural and cosmetic rust?

Structural rust affects load-bearing parts such as sills, floors, crossmembers, chassis legs and the areas around suspension and seat belt mountings. Cosmetic rust is on outer panels like door skins and bolt-on wings, which aren't load-bearing and usually only fail an MOT if they leave sharp edges.

How can I slow down rust?

Rinse the underside during winter to remove road salt, keep door and sill drain holes clear, and deal with stone chips early. On older cars, cavity wax in the sills and underbody protection make a real difference, and we can apply them.

Price your welding and rust repair now

Enter your reg and we’ll look up your car and price the job from our own labour rates and the book time for your model. Then book it in with a fixed written quote before any work starts.

  • Free, about 30 seconds, no sign-up
  • Parts, labour and VAT included
  • 12-month workmanship warranty
  • Collection from Beddington can be arranged
“It’s rare to find a garage you can truly trust. Fair price, brilliant customer service.”Thinushan K. · ★★★★★ Google

Prefer to talk? Call 020 4629 9469 or WhatsApp us.

Chat on WhatsApp