Car raised on the ramp for underbody inspection at KITH Cars Garage & Bodyworks, Hackbridge

Rust and Welding Repairs for Norbury Cars

A damp carpet is often the first sign of a rusting floor pan, and cars that have been through deep standing water after heavy rain are more at risk. We're about 18 minutes from Norbury in Hackbridge, and we find the cause before we weld.

  • ~18 min from Norbury
  • Mon–Fri 8am–8pm · Sat 8am–5pm
Loading instant quote…

Heavy rain, wet floors and hidden floor pan rust in Norbury

Norbury Brook, the River Graveney, runs under London Road at Hermitage Bridge and can rise quickly after heavy rain. You don't need to have driven through a flood for it to matter, but if you ever meet deep standing water on a road near the brook, it's worth avoiding. Water forced up into the sills and floor seams at speed sits there for weeks, and wet sound-deadening and carpet hold moisture against the floor pan from above. The same applies to deep puddles on any low-lying road after a downpour.

More often, damp comes from the car itself. Door seals, blocked drains and failing windscreen seals all let water in, and on the narrow 20mph roads around Norbury Avenue and Pollards Hill Park, most cars are parked outside in all weather. A soggy footwell that's been ignored for a winter or two is where we find floor pans rusting through from the inside. Cars parked near Norbury station for the commute can sit for long days in the rain, and older ones with tired seals let in more than their owners realise. Wet leaves from the trees around Norwood Grove also block scuttle drains.

So we start by finding the source. We lift the carpets where needed, check the seals and drains, and inspect the floor and sills from underneath. If the floor has rusted, we cut out the damaged area back to sound metal, weld in a new section, seam seal and protect it on both sides. There's little point welding a floor if the leak that caused it is still there, so we'll tell you about that too.

The drive from Norbury is longer, down the A23 and across Mitcham Common, and a car with a dangerous corrosion defect shouldn't make it. Collection and delivery can be arranged. Every repair comes with a written quote first and our 12-month workmanship warranty. We'll phone before doing extra work if more rust appears once we've cut in.

Welding & Rust Repair: what’s involved

Most cars have a monocoque body, meaning the shell itself acts as the chassis. Sills, floor pans, crossmembers and the areas around suspension and seat belt mountings carry load, so rust there weakens the car. Corrosion usually starts where water and road salt collect: inside sills, behind arch liners, along seams and around jacking points, and it often works from the inside out.

The MOT treats corrosion seriously. Excessive corrosion in load-bearing structure is a failure, particularly within 30cm of prescribed areas such as suspension, steering and seat belt mounting points. A proper repair means cutting back to sound metal, fitting a new steel section and welding it in, then sealing and protecting it inside and out. Covering rust with filler or a plate over rotten metal doesn't fix it, and a tester can fail an inadequate repair on a structural area.

From £80Written quote first
2 hours – 3 daysTypical time in the workshop
3 monthsWorkmanship warranty

Signs of rust that needs welding

Bubbling paint on sills or arches

Rust forming underneath the paint. It's usually more extensive than the visible bubbles suggest.

Holes or flaking metal underneath

Floor pans, sills, jacking points and crossmembers that flake or can be pushed through with a probe.

MOT advisory or failure for corrosion

An advisory is a warning worth acting on; a failure for structural corrosion must be repaired before the car can pass.

Soft or crumbling jacking points

If the sill crushes or the jack sinks into it, the structure around it is weakened.

Rust around suspension mountings

Corrosion near spring seats, strut tops, subframe or trailing arm mounts is structural and needs prompt repair.

Water in the footwells

Can be caused by holes in the floor, although blocked drains and door seals are more common causes, so we check.

Rust on door bottoms and boot floor

Often cosmetic rather than structural, but cheapest to repair while the rusted area is still small.

When should it be done?

Deal with structural rust as soon as it's found, ideally before the MOT so you have time to plan. Corrosion advisories are worth acting on, because another winter of salted roads can turn an advisory into a failure needing bigger repairs. Cosmetic rust on door bottoms or arch edges isn't a safety issue, but it's cheapest to fix while it's still at the bubbling stage. Older and classic cars benefit from a regular underside inspection.

  • MOT advisory mentioning corrosion: before the next winter or MOT
  • MOT failure for corrosion: before retest, and before driving at all if the defect was rated dangerous
  • Bubbling paint on sills, arches or door bottoms: while the rust is still small
  • Buying an older or classic car: underside inspection before or soon after purchase

How we repair rust and welding

  1. Inspection on the rampWe examine the underside, probe suspect areas and read any MOT failure sheet, separating structural corrosion from cosmetic.
  2. Written quoteWe explain what's structural, what's cosmetic and what should be prioritised. Rust sometimes proves more extensive once cut into, and we'll contact you before doing anything extra.
  3. Access and protectionTrim, arch liners, seats or carpets are removed as needed, and fuel lines, brake pipes and wiring are protected or moved away from heat.
  4. Cut out corrosionRusted metal is cut back until we reach clean, sound steel.
  5. Fabricate or fit repair sectionsNew steel sections are formed in the workshop, or pre-formed repair panels are used where available and a good fit.
  6. Weld inThe new metal is MIG welded in, seam welded where the structure requires it, and the welds are dressed back.
  7. Seal and protectJoints are seam sealed and primed, the underside is coated with underbody protection and enclosed sections are treated with cavity wax.
  8. Refit, check and hand overEverything is refitted, pipes and wiring are checked, and we explain what was repaired and anything else worth watching.

Steel and materials

Repairs are made with new steel of a suitable thickness for the area, either fabricated in the workshop or using pre-formed repair panels where they're available and fit well. After welding, joints are sealed, primed and protected with underbody coating, and enclosed sections such as sills are treated with cavity wax, which creeps into seams to slow future corrosion from the inside.

  • New steel sheet of the appropriate thickness
  • Pre-formed sill and arch repair panels where suitable
  • Weld-through primer and anti-corrosion primer
  • Seam sealer
  • Underbody protection and cavity wax

How long it takes

2 hours – 3 days

A single small MOT repair can often be done in 2–4 hours. Sills, floor sections or several areas can take 1–3 days, and extensive work on older cars longer. If the rust turns out to be worse once cut out, we'll call you before going further.

What’s included

  • Underside inspection and written quote
  • Cutting out corrosion back to sound metal
  • New steel welded in
  • Seam sealing, priming and underbody protection on the repair
  • Cavity wax in enclosed sections that have been repaired
  • 12-month workmanship warranty

From Norbury to our Hackbridge workshop

Take London Road (A23) south to Thornton Heath Pond, then Thornton Road (A23) to the Lombard roundabout and turn onto Mitcham Road (A236) westbound. Stay on the A236 as it becomes Croydon Road across Mitcham Common, then turn left at the roundabout onto Carshalton Road (A237), which becomes London Road through Hackbridge; Soho Mills is on the left. A shorter but slower residential route runs via Northborough Road and Pollards Hill to Mitcham Common.

Take London Road (A23) to Thornton Heath Pond and the Lombard roundabout, then the A236 across Mitcham Common and Carshalton Road into Hackbridge, around 18 minutes. For a car that shouldn't be driven, ask about collection from Norbury.

Directions from Norbury

About Norbury

Norbury is a largely residential suburb at the northern tip of the London Borough of Croydon, sharing the SW16 postcode with neighbouring Streatham; most of it lies in Croydon, with some parts on the Streatham side falling within Lambeth. It grew rapidly in the early 1900s, and its streets are mostly Edwardian and inter-war terraces and semis, including the London County Council's first cottage estate, with larger houses on the slopes of Pollards Hill. The A23 London Road forms the spine of the area and its main shopping strip, and it is often congested, while the side roads are quiet, 20mph and heavily parked. It is a family-orientated area with a busy, independent high street.

Places nearby: Norbury station, Norbury Park, Norbury Hall, Norwood Grove, Pollards Hill Park, Hermitage Bridge and Norbury Brook

Postcodes: SW16 · Mainly the London Borough of Croydon (Norbury and Pollards Hill, and Norbury Park wards), with some parts on its Streatham side extending into the London Borough of Lambeth

More about KITH for Norbury drivers

Welding & Rust Repair in Norbury: your questions answered

My carpet is wet. Is the floor rusted through?

Not necessarily. Leaking door seals, blocked drains and windscreen seals are more common causes. We check those first and inspect the floor from above and below, then repair whatever is actually at fault.

I drove through deep water after a storm. Should I worry about rust?

It's worth having the underside and the inside of the sills checked, and the carpets dried if they got wet. Trapped water speeds up corrosion. Catching it early avoids a bigger welding job later.

Is 18 minutes too far to bring a car with rust problems?

No, if it's safe to drive, the route via the A23 and Mitcham Common is straightforward. If the MOT rated the defect as dangerous, don't drive it. We can collect it from Norbury instead.

Will my car pass the MOT after welding?

We repair the items on your failure sheet to a standard that meets the MOT inspection requirements, although the tester makes the final decision at the retest. If we find other corrosion nearby that's likely to cause a problem, we'll point it out before the retest.

Is it worth welding an older car?

It depends on how much rust there is and what the car is worth. A couple of sill repairs on an otherwise sound car are usually worthwhile. Widespread corrosion across floors, sills and mountings can cost more than the car is worth, and we'll give you an honest view.

Can you just patch over the rust?

Not on structural areas. Welding a plate over rotten metal traps moisture so the rust carries on underneath, and a tester can fail it as an inadequate repair. We cut out to sound metal and weld in new steel.

What's the difference between structural and cosmetic rust?

Structural rust affects load-bearing parts such as sills, floors, crossmembers, chassis legs and the areas around suspension and seat belt mountings. Cosmetic rust is on outer panels like door skins and bolt-on wings, which aren't load-bearing and usually only fail an MOT if they leave sharp edges.

How can I slow down rust?

Rinse the underside during winter to remove road salt, keep door and sill drain holes clear, and deal with stone chips early. On older cars, cavity wax in the sills and underbody protection make a real difference, and we can apply them.

Price your welding and rust repair now

Enter your reg and we’ll look up your car and price the job from our own labour rates and the book time for your model. Then book it in with a fixed written quote before any work starts.

  • Free, about 30 seconds, no sign-up
  • Parts, labour and VAT included
  • 12-month workmanship warranty
  • Collection from Norbury can be arranged
“It’s rare to find a garage you can truly trust. Fair price, brilliant customer service.”Thinushan K. · ★★★★★ Google

Prefer to talk? Call 020 4629 9469 or WhatsApp us.

Chat on WhatsApp