Ford van in for engine mount and manifold gasket work at KITH Cars Garage & Bodyworks, Hackbridge

Exhaust repairs in South London, section by section

A blowing exhaust is one of the few faults where finding it matters as much as fixing it. Hot gas escaping from a pinhole can sound like a failed silencer, a cracked flexi pipe can sound like a manifold, and a catalyst efficiency code frequently has nothing to do with the catalyst. So the car goes in the air with the engine running and we locate the leak properly before anything is ordered. You see the failure yourself, the price is written down before we start, and exhaust work here begins at £150.

  • From £205 · 1–3 hours
  • Mon–Fri 8am–8pm · Sat 8am–5pm
Loading instant quote…
From £205Written quote before we start
1–3 hoursTypical time in the workshop
3 monthsWorkmanship warranty
17 areasCollection across South London

The leak found before parts

We locate and confirm the leak on the ramp first. Ordering a silencer because the car sounds loud is how people end up paying twice for the same noise.

You see it on the ramp

Come under the car with us and look at the hole, the split or the broken bracket. Nobody should have to take a corroded pipe on trust.

Seized fixings priced into the quote

Rusted studs and clamps are normal on an exhaust, so we account for them upfront instead of springing an extra charge on you once the car is in pieces.

No cat or filter removals

We do not gut catalytic converters or particulate filters for anyone. If the car needs one, it gets a type-approved replacement or it goes elsewhere.

How we handle exhaust repair at Hackbridge

Leak hunting is done hot, cold and with the engine running. Sound on its own is misleading, so we feel along the joints with a gloved hand for pulses of gas, look for the soot trail that marks where a joint has been blowing, and briefly raise back pressure at the tailpipe so a small hole announces itself. Temperature matters too. A split that closes up as the metal expands will only show in the first minute from cold, which is why we ask you to bring the car in cold where you can rather than after a long run.

Corrosion decides how the job goes. Manifold studs, clamp bolts and lambda sensors seize into their threads, so we work with heat and penetrating fluid and, where a fixing is past saving, a nut splitter or a cutting disc rather than force that snaps a stud off flush with the head. If a neighbouring section looks likely to break up once it is disturbed, we say so before we start and tell you what that would add, so the figure you agreed to is not overtaken halfway through. If a stud does shear, we quote the extraction rather than quietly folding it into the bill.

Cutting out a catalytic converter or a particulate filter, or fitting an empty pipe where one belongs, is work we decline outright, because the vehicle then has no legal place on the road and it is the owner who carries that. A catalyst is not condemned on a fault code alone either: the sensor readings, the fuel trims and any leak upstream get checked first, since a cat fitted to an engine that is still burning oil or coolant will simply fail again. New sections go on loose, are aligned clear of the floorpan, driveshafts and heat shields, then tightened once everything sits where it should.

Exhaust Repairs: what’s involved

An exhaust does more than carry fumes away. The manifold collects gases from the engine, the catalytic converter cleans them, and on diesels the DPF traps soot. Silencers reduce noise, a flexible section absorbs engine movement, and rubber hangers hold everything clear of the body. Lambda sensors before and after the catalyst tell the ECU how well the engine is burning fuel and whether the catalyst is working.

Exhausts live in a harsh place. Short journeys leave acidic condensation sitting inside silencers, road salt attacks the outside, and speed bumps and kerbs knock pipes out of line. A leak changes more than the noise. It can let fumes into the cabin, upset lambda sensor readings and cause an MOT failure. Catalytic converters are also targeted by thieves, particularly on some hybrids, and a stolen cat needs replacing before the car can be driven legally.

Signs your exhaust needs attention

Louder engine or blowing noise

A deeper roar or a chuffing noise that rises with engine speed usually means a hole, a failed joint or a split flexi pipe.

Rattling underneath

Loose heat shields, broken clamps or a collapsed internal baffle in a silencer all rattle, often most noticeably at idle or over bumps.

Exhaust hanging low or knocking

Perished rubber hangers or broken brackets let the system drop and knock against the floor or suspension.

Fumes smell in the cabin

A leak near the front of the system can draw fumes into the car. This needs checking promptly because exhaust gas contains carbon monoxide.

Engine light with catalyst or lambda codes

Catalyst efficiency and lambda sensor codes can mean a failing cat, a faulty sensor or an air leak upstream of the sensor that upsets its readings.

Sudden very loud noise on start-up

An exhaust that sounds dramatically louder overnight, especially on a hybrid, may mean the catalytic converter has been cut out.

Visible rust or holes

Heavy scaling, holes in silencer boxes and corroded joints are usually spotted at service or MOT before they start to blow.

When should it be done?

There is no fixed replacement interval for an exhaust. Life depends on the materials, the car and how it is used, with lots of short trips shortening it most. Get the system checked as soon as the note changes, something is rattling or hanging low, or you smell fumes. A leak or insecure exhaust is an MOT failure, so it makes sense to deal with it before the test rather than after.

  • Any change in exhaust noise, blowing or rattling
  • Fumes smell inside the car
  • Catalyst or lambda sensor fault codes
  • Advisories for corrosion or insecure mountings at MOT or service
  • After suspected catalytic converter theft

How we repair an exhaust

  1. Check-in and listenWe ask what you have noticed and listen to the car running, as the type of noise often points to the area of the leak.
  2. Lift and inspectWith the car on a ramp we inspect the whole system, from the manifold back, including joints, flexi pipe, silencers, hangers, heat shields and sensors.
  3. Check codes where relevantIf there are catalyst or lambda codes we scan the car and check sensor data, so we don't replace a cat when the cause is a sensor or a leak.
  4. Written quoteWe explain which sections need replacing and why, and give you a written quote. Where a section is sound, we keep it.
  5. Remove the old sectionsWe remove the failed parts, cutting seized fixings where necessary, and inspect the joints and brackets we are connecting to.
  6. Fit new partsWe fit the new sections with new gaskets, clamps and hangers, aligning the system so it sits clear of the body and doesn't knock.
  7. Leak test and road testWe run the engine and check every joint for leaks, clear any related codes and road test the car to check for noise and knocks.

Parts we fit

We fit OE or OE-equivalent exhaust parts made to fit the vehicle properly, such as Bosal, Walker or BM Catalysts, rather than universal sections that need bodging to fit. Replacement catalytic converters are type-approved for the vehicle so it meets its emissions standard. We always renew gaskets, clamps and rubber hangers when fitting a new section, as reusing old ones is a common cause of leaks.

  • Vehicle-specific front pipes, centre sections and rear silencers
  • Flexi pipes and manifold gaskets
  • Type-approved catalytic converters
  • Lambda (oxygen) sensors
  • New clamps, gaskets and rubber hangers

How long it takes

1–3 hours

A rear silencer or flexi pipe is often done in an hour or two. Catalytic converters, manifolds and badly seized systems take longer, and some parts may need ordering in.

What’s included

  • Full inspection of the exhaust system on a ramp
  • Written quote before any work starts
  • Removal of failed sections
  • New gaskets, clamps and hangers as required
  • Leak check with the engine running
  • Road test

What people get wrong about exhaust repair

Treating exhaust paste as a repair

Paste and bandage tape will seal a pinhole for a few weeks at most, and the metal around that pinhole is already thin. It is a reasonable way of getting home and no sort of fix.

Replacing the cat because of the code

A catalyst efficiency code often turns out to be a lazy rear lambda sensor or an air leak drawing fresh air past it. Fitting a converter without checking is an expensive way of keeping the same warning light.

Splicing in a universal lambda sensor

Universal sensors joined into the loom frequently read differently from the correct part and can set heater circuit faults of their own. The vehicle-specific sensor with the right connector costs more once.

Fitting a louder back box for power

Changing the rear silencer alters the note and very little else, because the restriction that matters is further forward. Excessive noise is also an MOT failure in its own right.

Price your exhaust repair now

Enter your reg and we’ll look up your car, then price the job from our own labour rates and the book time for your model. Nothing is booked until you say so, and the written quote comes before any work.

  • Free, about 30 seconds, no sign-up
  • Parts, labour and VAT included
  • 3-month workmanship warranty
  • Collection and delivery across South London
“It’s rare to find a garage you can truly trust. Fair price, brilliant customer service.”Thinushan K. · ★★★★★ Google

Prefer to talk? Call 020 4629 9469 or WhatsApp us.

Exhaust Repairs: your questions answered

Is this a same-visit job or do you keep the car?

A rear silencer, a flexi pipe or a set of mountings is usually a wait-while-you-are-here job when the part is on the shelf or can be collected that morning. Manifolds, catalytic converters and badly seized systems are better left with us for the day. We tell you which when we quote, and we can collect the car locally instead if that is easier.

Is a stainless steel system worth paying extra for?

It depends how long you intend to keep the car. Stainless resists both the internal condensation and the road salt that finish off a standard system, so on a car you plan to hold onto it can outlast the original by a long way. On a car you will sell next year, a good OE-equivalent section is better value. We quote both where a stainless option exists for your vehicle.

What does the written quote actually include?

The sections being replaced, the clamps, gaskets and hangers that go with them, the labour, and anything already visible that may need doing at the same time. Nothing else gets added without a phone call. If a hidden problem appears once we are into the job, we stop, explain it and quote it separately.

What happens if it blows again afterwards?

The work we did is warranted for three months. Separately from that, the section, flexi or mounting we fitted comes with the supplier's own terms, which we set out at the time rather than leave you to find. A joint we made that starts to leak is ours to put right. A different part of the old system corroding through later is a separate repair, which is exactly why we point out marginal sections when we quote.

Do I need a whole new exhaust?

Usually not. Exhausts are made in sections, and we only replace the parts that have failed. If a neighbouring section is badly corroded and likely to break when disturbed, we will tell you and let you decide.

Can you weld my exhaust instead?

Sometimes, where the pipe around a small hole or split is still sound. On thin, corroded silencers a weld often won't last, so a new section is better value. We'll give you an honest view once we see it.

Will an exhaust leak fail the MOT?

Yes. A leaking exhaust, an insecure system or a missing catalytic converter where one was fitted as standard is an MOT failure. Excessive noise and failing the emissions test are also reasons for failure.

My catalytic converter was stolen. What now?

Don't drive the car far. It will be very loud and may run poorly, and it isn't legal on the road without its cat. Report the theft to the police and your insurer, then we can quote for a type-approved replacement.

Do you replace DPFs too?

Yes, where a diesel particulate filter is damaged or too ash-loaded to clean we can quote for replacement. If it is simply blocked with soot, cleaning may be the better option, which we cover under our DPF cleaning service.

What our customers say

What customers have said about us

★★★★★

“BMW 1 Series needed a new timing chain and clutch. Fair price, courtesy car offered. Stands out from most garages.”

Aaron Konadu
★★★★★

“Professional, no upselling, everything explained clearly. Work completed same day and car runs perfectly.”

Ziaur Rahman
★★★★★

“Rare to find a garage you can truly trust. Fair price, brilliant service.”

Thinushan Keitheswaran
Read all reviews on Google ★★★★★
Chat on WhatsApp