Jaguar in for a timing chain replacement at KITH Cars Garage & Bodyworks, Hackbridge

Timing chain replacement in South London, measured before we quote

A timing chain job is a large bill on a car that may still drive perfectly well, so the first thing worth establishing is whether the chain is genuinely worn. Plenty of rattles turn out to be a tensioner, an auxiliary belt or a pulley, and plenty of timing codes turn out to be a sensor or sludged oil galleries. At our Hackbridge workshop we measure before we recommend, and if the chain does need doing you get one written price, from £1025, covering the whole job rather than a figure that grows once the covers are off.

  • From £1025 · 1–3 days
  • Mon–Fri 8am–8pm · Sat 8am–5pm
Loading instant quote…
From £1025Written quote before we start
1–3 daysTypical time in the workshop
3 monthsWorkmanship warranty
17 areasCollection across South London

Wear measured, not assumed

Live cam and crank deviation figures are compared against the manufacturer's limits before we recommend the job. A rattle on its own is a symptom, not a diagnosis.

One price for the whole job

The quote covers the kit, the labour, the gaskets and seals disturbed and the oil, so there is no stack of extras at the end. Anything found worn inside is priced for your decision first.

Nothing worn goes back in

Guides, tensioner and stretch bolts are renewed as a matter of course. Leaving an original tensioner in with a new chain is how these jobs come back a year later.

A straight answer on value

On a high-mileage car with other problems we will tell you where the money is better spent, even when that means we do not get the work.

How we handle timing chain replacement at Hackbridge

Chain work is booked in as a block rather than squeezed between other jobs, because the engine sits stripped and open. Before anything comes apart we listen from stone cold, in the first two or three seconds after the key turns, which is when a worn chain and a drained tensioner give themselves away. We scan for stored correlation and camshaft adjuster codes and read the live deviation figures where the engine reports them. If those numbers sit inside the manufacturer's tolerance and the noise is coming from somewhere else, we say so, and you have saved yourself a very large bill.

Once the job is on, cleanliness decides how long the repair lasts. The sump and the cambox are covered while the old chain comes out, and anything that has shed material gets followed up: on engines where broken guide plastic is known to travel, we look at the pick-up and strainer rather than hoping. Chain, guides and tensioner go in as a set, with sprockets and adjusters where they are worn. Stretch bolts on camshaft sprockets and covers are replaced rather than reused, the timing is verified by hand through two full turns, and adaptations are reset on the scan tool.

Two things get talked through before you commit. The first is access: some engines are a day's work from the front of the car, others need the engine or the gearbox out because the chain sits at the flywheel end, and that difference is most of the price. The second is whether the car is worth it, which you will get a straight answer on rather than a sales pitch. If we go ahead, the engine leaves with fresh oil to the correct approval and a new filter, and we will tell you plainly what oil interval to keep to, because that is what wears the next chain.

Timing Chain Replacement: what’s involved

A timing chain does the same job as a cambelt, keeping the crankshaft and camshafts in exact step, but it is a metal chain running inside the engine in oil. It is guided by plastic-faced rails and kept tight by a tensioner, usually fed by engine oil pressure. Chains have no fixed replacement interval and are meant to last a long time, but that depends on clean oil at the right level.

Over time the chain's pins and bushes wear, which lengthens the chain and is known as stretch. The guides wear and the tensioner can no longer take up the slack. The cam timing drifts, which the engine management picks up, and eventually the chain can jump a tooth or break. On most engines that means pistons hitting valves. Caught early, a chain replacement is a planned repair rather than an engine rebuild.

Signs of a worn timing chain

Rattle on cold start

A metallic rattle for a few seconds after a cold start, before oil pressure builds in the tensioner, is the classic early sign. If it lasts longer or gets louder, the chain or tensioner is worn.

Cam and crank correlation fault codes

Codes such as P0016 to P0019 mean the engine computer sees the camshaft and crankshaft positions drifting apart, which is typical of a stretched chain.

Engine management light

The light may come on with timing, camshaft sensor or variable valve timing codes, sometimes before any noise is obvious.

Rattle or whine when warm

A persistent rattle at idle or a whine that rises with revs when the engine is warm suggests a worn tensioner, broken guide or a very stretched chain.

Rough running or loss of power

Incorrect cam timing can cause misfires, hesitation, poor starting and reduced power.

Metal or plastic fragments in the oil

Pieces of broken guide can turn up at an oil change, and debris can block the oil pick-up.

Known engine with high mileage

Some engines have a history of chain problems, and at higher mileages we recommend checking chain wear even without symptoms.

When should a timing chain be replaced?

Unlike a cambelt, a timing chain has no scheduled replacement interval. It is replaced when there is evidence of wear: noise, fault codes, or measured timing deviation outside the manufacturer's limits. How long a chain lasts depends heavily on oil. Long service intervals, the wrong specification of oil or running with the level low all speed up wear. Some engines are known for chain problems, so on those we check chain wear at higher mileage or when buying a used car, not just when the rattle starts.

  • No fixed interval; replace when wear is confirmed
  • Check immediately if you hear a rattle on cold start that lasts more than a few seconds
  • Investigate any cam and crank correlation fault codes
  • Consider a check at higher mileage on engines known for chain wear
  • Short oil change intervals with the correct oil help chains last

How we replace a timing chain

  1. Listen and scanWe listen to the engine from cold and read fault codes with dealer-level diagnostic equipment, including stored freeze-frame data.
  2. Measure chain wearWhere the engine supports it, we read live camshaft and crankshaft deviation values and compare them with the manufacturer's limits. On some engines we inspect the tensioner or guides directly.
  3. Written quoteWe explain what we found and quote for the full kit and labour, including whether the engine needs to come out to reach the chain.
  4. Lock the timing and strip downThe engine is locked with engine-specific timing tools and the timing cover and ancillaries are removed. On some engines, such as BMW's N47 diesel, the chain is at the gearbox end and the engine is usually removed.
  5. Replace chain and componentsWe fit a new chain, guides and tensioner, and replace sprockets, variable valve timing units or oil pump drive parts where worn or included in the kit.
  6. Seals, gaskets and oilAll gaskets and seals disturbed are renewed, and the engine is refilled with the correct specification oil and a new filter.
  7. Verify timing and resetThe engine is turned by hand to confirm the timing, then fault codes are cleared and any adaptation values reset with diagnostic equipment.
  8. Road test and handoverWe run the engine from cold, recheck the live timing data, road test and explain the work, with advice on oil change intervals.

Timing chain parts we fit

We fit complete OE or OE-equivalent timing chain kits from suppliers such as Iwis, INA and Febi, which include the chain, guides and tensioner so no worn part is left behind. Where sprockets, camshaft adjusters or the oil pump chain are worn, we tell you and quote for them. Every job finishes with fresh oil to your manufacturer's approval — Castrol, in the grade your engine requires, and a new filter.

  • Timing chain, guides and tensioner
  • Sprockets and camshaft adjusters where worn
  • Timing cover gaskets and crankshaft seal
  • Engine oil to manufacturer approval and new oil filter
  • Coolant where the cooling system is disturbed

How long it takes

1–3 days

Engines with the chain at the front can often be done in a day. Rear-mounted chains or engines that must be removed, such as the BMW N47, typically take 2–3 days. We confirm the timing when we quote.

What’s included

  • Cold-start listening check and full fault code scan
  • Live timing data check where the engine supports it
  • Complete chain kit fitted
  • New gaskets and seals where disturbed
  • Oil and filter change
  • Road test and 3-month workmanship warranty

What people get wrong about timing chain replacement

Fitting a tensioner and hoping

A new tensioner takes up slack for a while and quietens the rattle, which is why it gets tried. It does nothing about worn guides or a chain that has already lengthened, and the noise returns.

Extended oil intervals are harmless

The chain is lubricated and tensioned by engine oil. Long intervals, the wrong specification, or a level left low for months do far more damage than mileage alone.

Throwing sensors at a timing code

Correlation codes send people through camshaft sensors, solenoids and adjusters. Those parts do fail, but the code is describing a timing relationship, and it is worth measuring that before buying anything.

The noise stopped, so it is fine

A hydraulic tensioner pumps up as soon as oil pressure arrives and the rattle disappears within seconds. That is the tensioner doing its job on a worn chain, not the chain recovering.

Price your timing chain replacement now

Enter your reg and we’ll look up your car, then price the job from our own labour rates and the book time for your model. Nothing is booked until you say so, and the written quote comes before any work.

  • Free, about 30 seconds, no sign-up
  • Parts, labour and VAT included
  • 3-month workmanship warranty
  • Collection and delivery across South London
“It’s rare to find a garage you can truly trust. Fair price, brilliant customer service.”Thinushan K. · ★★★★★ Google

Prefer to talk? Call 020 4629 9469 or WhatsApp us.

Timing Chain Replacement: your questions answered

Can you keep me on the road while the car is in?

Bring it up at the point of booking. Courtesy cars depend on what has come back that week, and we also hire vehicles out by the day from the same site, which suits a job that runs across more than one day. If the car is still driveable we can collect it locally too.

Is the quote fixed, or can it change once you are inside the engine?

The figure covers the chain kit and the labour for the work described, and that does not move. What can change is what we find: a scored sprocket, a worn oil pump chain or a damaged adjuster. Those are priced and put to you for a decision before they go anywhere near the engine.

What does the guarantee cover on a job this size?

A year on the way the job was assembled, with the chain kit backed separately by whoever manufactured it. What nobody can guarantee is the rest of an engine that has been run on a worn chain, so if we see signs of wear elsewhere, such as low oil pressure or bearing noise, you will hear about it before you spend the money.

I am buying a used car with a known chain engine. Can you check it first?

Yes, and it is worth doing before you hand the money over rather than after. We listen from cold, scan for stored timing codes and read the deviation values where the engine supports it, which tells you far more than a test drive around the block. Bring it to us or arrange for the seller to meet you here.

Aren't timing chains supposed to last the life of the engine?

Many do, but it relies on regular oil changes with the right oil. Chains wear gradually, and some engine designs are known to wear chains or tensioners early. There is no service interval, so replacement is based on symptoms and measurements.

Is the Peugeot and Citroën 1.2 PureTech a timing chain engine?

No. The three-cylinder 1.2 PureTech uses a timing belt that runs in oil, known as a wet belt. It has a replacement interval and its own common faults, so it is handled as a cambelt job rather than a chain replacement.

Which engines are known for timing chain problems?

Well-known examples include BMW's N47 diesel, early VW Group 1.2 and 1.4 TSI petrol engines, early 1.8 and 2.0 TFSI engines, and the 1.6 turbo petrol used by BMW MINI, Peugeot and Citroën. Plenty of these run fine, so we diagnose each car rather than assume.

Can I keep driving with a timing chain rattle?

A brief rattle on cold start can go on for a while, but it tells you wear has begun. A rattle that lasts longer, a warning light or timing fault codes mean you should book in soon. The cost of waiting can be the engine.

What is the BMW N47 problem?

The N47 diesel has its timing chain at the back of the engine, next to the gearbox. Chain and guide wear there causes a rattle, often heard from the rear of the engine, and fixing it usually means removing the engine. We quote these as a complete job with all chains, guides and tensioners.

What our customers say

What customers have said about us

★★★★★

“BMW 1 Series needed a new timing chain and clutch. Fair price, courtesy car offered. Stands out from most garages.”

Aaron Konadu
★★★★★

“Professional, no upselling, everything explained clearly. Work completed same day and car runs perfectly.”

Ziaur Rahman
★★★★★

“Rare to find a garage you can truly trust. Fair price, brilliant service.”

Thinushan Keitheswaran
Read all reviews on Google ★★★★★
Chat on WhatsApp