Car raised on the ramp for underbody inspection at KITH Cars Garage & Bodyworks, Hackbridge

Welding and rust repair in South London, back to sound metal

Rust is the one repair nobody can see the whole of from the outside, because a sill rots from the inside and the paint is the last thing to go. What we can do is show you what is there now, say what we expect to find behind it, and price each area on its own so you can choose the order the work is done in. The welding happens in our bodyshop at Soho Mills in Hackbridge, on MOT failures, structural corrosion around mountings, and the bubbling arches and door bottoms that are still cheap to catch. From £80.

  • From £80 · 2 hours – 3 days
  • Mon–Fri 8am–8pm · Sat 8am–5pm
Loading instant quote…
From £80Written quote before we start
2 hours – 3 daysTypical time in the workshop
3 monthsWorkmanship warranty
17 areasCollection across South London

Each area priced on its own

Sills, floor, arches and mountings are quoted separately, so the structural work can be done now and the cosmetic later, or spread across two visits.

Failure sheets priced line by line

Bring the sheet with you. Every item on it gets a figure against it, and we will point out which of the advisories are about to become failures.

Factory joints, not patches

Plug welds where the car was spot welded, a continuous seam where the structure calls for one, and repair sections made to fit the hole rather than the other way round.

Bodyshop and MOT on one site

The welding, the paintwork afterwards and the test itself are handled here, so the car is not shuttled between two places and two sets of bookings.

How we handle welding and rust repair at Hackbridge

Preparation takes considerably longer than the welding. The battery is disconnected, fuel lines, brake pipes and looms near the repair are moved or shielded, carpets and sound deadening are pulled well back from the underside of a floor repair, and an extinguisher stays with the car for the whole job, because the wadding under a carpet will smoulder for a long time before anybody smells it. Where a repair sits close to the tank, the tank comes out rather than being worked around.

The metal itself is straightforward as long as nothing is rushed. Corrosion is cut back until the grinder finds bright steel rather than brown, the new section is made to fit the hole instead of the hole being opened up to suit a panel, mating faces get weld-through primer, and the joint is made the way the factory made it: plug welds where the original was spot welded, and a continuous seam where the structure calls for one. Welds are dressed back just enough to sit flush, because grinding them flat looks tidy and takes the strength straight back out of the job.

Then it is protected inside and out, which is the part that decides whether you are back in five years. Rust does not get buried here: no filler across a structural area, no fresh underseal sprayed over corrosion to hide it, and no aluminium panel welded as though it were steel, so tell us if the wing or bonnet is alloy. Each area is quoted on its own, so the sills can be done now and the boot floor next year, and if you arrive with an MOT failure sheet we work through it line by line and put a price against every item.

Welding & Rust Repair: what’s involved

Most cars have a monocoque body, meaning the shell itself acts as the chassis. Sills, floor pans, crossmembers and the areas around suspension and seat belt mountings carry load, so rust there weakens the car. Corrosion usually starts where water and road salt collect: inside sills, behind arch liners, along seams and around jacking points, and it often works from the inside out.

The MOT treats corrosion seriously. Excessive corrosion in load-bearing structure is a failure, particularly within 30cm of prescribed areas such as suspension, steering and seat belt mounting points. A proper repair means cutting back to sound metal, fitting a new steel section and welding it in, then sealing and protecting it inside and out. Covering rust with filler or a plate over rotten metal doesn't fix it, and a tester can fail an inadequate repair on a structural area.

Signs of rust that needs welding

Bubbling paint on sills or arches

Rust forming underneath the paint. It's usually more extensive than the visible bubbles suggest.

Holes or flaking metal underneath

Floor pans, sills, jacking points and crossmembers that flake or can be pushed through with a probe.

MOT advisory or failure for corrosion

An advisory is a warning worth acting on; a failure for structural corrosion must be repaired before the car can pass.

Soft or crumbling jacking points

If the sill crushes or the jack sinks into it, the structure around it is weakened.

Rust around suspension mountings

Corrosion near spring seats, strut tops, subframe or trailing arm mounts is structural and needs prompt repair.

Water in the footwells

Can be caused by holes in the floor, although blocked drains and door seals are more common causes, so we check.

Rust on door bottoms and boot floor

Often cosmetic rather than structural, but cheapest to repair while the rusted area is still small.

When should it be done?

Deal with structural rust as soon as it's found, ideally before the MOT so you have time to plan. Corrosion advisories are worth acting on, because another winter of salted roads can turn an advisory into a failure needing bigger repairs. Cosmetic rust on door bottoms or arch edges isn't a safety issue, but it's cheapest to fix while it's still at the bubbling stage. Older and classic cars benefit from a regular underside inspection.

  • MOT advisory mentioning corrosion: before the next winter or MOT
  • MOT failure for corrosion: before retest, and before driving at all if the defect was rated dangerous
  • Bubbling paint on sills, arches or door bottoms: while the rust is still small
  • Buying an older or classic car: underside inspection before or soon after purchase

How we repair rust and welding

  1. Inspection on the rampWe examine the underside, probe suspect areas and read any MOT failure sheet, separating structural corrosion from cosmetic.
  2. Written quoteWe explain what's structural, what's cosmetic and what should be prioritised. Rust sometimes proves more extensive once cut into, and we'll contact you before doing anything extra.
  3. Access and protectionTrim, arch liners, seats or carpets are removed as needed, and fuel lines, brake pipes and wiring are protected or moved away from heat.
  4. Cut out corrosionRusted metal is cut back until we reach clean, sound steel.
  5. Fabricate or fit repair sectionsNew steel sections are formed in the workshop, or pre-formed repair panels are used where available and a good fit.
  6. Weld inThe new metal is MIG welded in, seam welded where the structure requires it, and the welds are dressed back.
  7. Seal and protectJoints are seam sealed and primed, the underside is coated with underbody protection and enclosed sections are treated with cavity wax.
  8. Refit, check and hand overEverything is refitted, pipes and wiring are checked, and we explain what was repaired and anything else worth watching.

Steel and materials

Repairs are made with new steel of a suitable thickness for the area, either fabricated in the workshop or using pre-formed repair panels where they're available and fit well. After welding, joints are sealed, primed and protected with underbody coating, and enclosed sections such as sills are treated with cavity wax, which creeps into seams to slow future corrosion from the inside.

  • New steel sheet of the appropriate thickness
  • Pre-formed sill and arch repair panels where suitable
  • Weld-through primer and anti-corrosion primer
  • Seam sealer
  • Underbody protection and cavity wax

How long it takes

2 hours – 3 days

A single small MOT repair can often be done in 2–4 hours. Sills, floor sections or several areas can take 1–3 days, and extensive work on older cars longer. If the rust turns out to be worse once cut out, we'll call you before going further.

What’s included

  • Underside inspection and written quote
  • Cutting out corrosion back to sound metal
  • New steel welded in
  • Seam sealing, priming and underbody protection on the repair
  • Cavity wax in enclosed sections that have been repaired
  • 12-month workmanship warranty

What people get wrong about welding and rust repair

Underseal over rust protects it

Spraying a coating onto corroded metal seals the moisture in and hides what is happening underneath. On a car you are buying, fresh underseal is a reason to look harder rather than a selling point.

Sealant and foam will hold it

Filling a hole in a floor with sealant, expanding foam or a riveted plate keeps water in rather than out, and the surrounding metal goes in half the time. It also makes the eventual repair a bigger one.

Surface rust means structural rust

A light brown film on a subframe or a suspension arm is normal on any car that has seen a winter. What matters is metal that flakes in layers, sounds dull when tapped, or gives under a probe.

Leaving it until the MOT is due

Corrosion spreads fastest through a salted winter, and booking welding under retest pressure takes away your choice of when the car is off the road. It is the same work either way, done calmer and usually cheaper earlier.

Price your welding and rust repair now

Enter your reg and we’ll look up your car, then price the job from our own labour rates and the book time for your model. Nothing is booked until you say so, and the written quote comes before any work.

  • Free, about 30 seconds, no sign-up
  • Parts, labour and VAT included
  • 12-month workmanship warranty
  • Collection and delivery across South London
“It’s rare to find a garage you can truly trust. Fair price, brilliant customer service.”Thinushan K. · ★★★★★ Google

Prefer to talk? Call 020 4629 9469 or WhatsApp us.

Welding & Rust Repair: your questions answered

Do you paint the repair, or does it stay bare?

Underside work is sealed, primed and coated, which is the correct finish for that area and is not meant to be looked at. Where the repair is visible, such as an arch lip or a door bottom, it can be prepared and painted to match the car in the bodyshop, and that part is quoted separately from the welding.

Is the welding guaranteed?

Our workmanship carries a 12-month warranty, and that covers the areas we repaired. It cannot cover rust that starts somewhere else on a car that is corroding generally, so we always point out the areas we think are next, in writing, and you are not surprised by them a year later.

Can I keep driving it while I wait for a slot?

It depends what was found. Corrosion recorded as a dangerous defect means the car should not be driven at all, whether or not your old certificate is still in date. A major failure or an advisory is different: if your existing MOT has not expired, you can carry on while you wait for a date that suits you.

Do you take on older and classic cars?

Yes, and they are often the most satisfying work in the shop. Panel availability is what varies: some models have good reproduction sills and arches, others need sections fabricating here, and that changes the price more than the welding does. Send photographs of the worst areas and we will tell you which it is likely to be.

Will my car pass the MOT after welding?

We repair the items on your failure sheet to a standard that meets the MOT inspection requirements, although the tester makes the final decision at the retest. If we find other corrosion nearby that's likely to cause a problem, we'll point it out before the retest.

Is it worth welding an older car?

It depends on how much rust there is and what the car is worth. A couple of sill repairs on an otherwise sound car are usually worthwhile. Widespread corrosion across floors, sills and mountings can cost more than the car is worth, and we'll give you an honest view.

Can you just patch over the rust?

Not on structural areas. Welding a plate over rotten metal traps moisture so the rust carries on underneath, and a tester can fail it as an inadequate repair. We cut out to sound metal and weld in new steel.

What's the difference between structural and cosmetic rust?

Structural rust affects load-bearing parts such as sills, floors, crossmembers, chassis legs and the areas around suspension and seat belt mountings. Cosmetic rust is on outer panels like door skins and bolt-on wings, which aren't load-bearing and usually only fail an MOT if they leave sharp edges.

How can I slow down rust?

Rinse the underside during winter to remove road salt, keep door and sill drain holes clear, and deal with stone chips early. On older cars, cavity wax in the sills and underbody protection make a real difference, and we can apply them.

Can I choose my own repairer, or do I have to use the one my insurer names?

You choose. Insurers maintain their own approved networks and will steer you towards them, but the car is yours and so is the decision. Tell your insurer you are using KITH Cars and we will deal with them directly. Be aware of what changes: an insurer typically guarantees work done inside its own network, and outside it some policies ask you to cover a shortfall if our figure and theirs differ. Read your own policy wording, or send it to us and we will go through it with you before you commit to anything.

Is there a courtesy car while mine is in?

Yes, subject to availability, at 30 pounds plus VAT a day - 36 pounds a day all in. We would rather quote a real figure than advertise a free car and recover it somewhere else in the bill. Ask when you book and we will tell you straight away whether one is free for your dates.

What our customers say

What customers have said about us

★★★★★

“BMW 1 Series needed a new timing chain and clutch. Fair price, courtesy car offered. Stands out from most garages.”

Aaron Konadu
★★★★★

“Professional, no upselling, everything explained clearly. Work completed same day and car runs perfectly.”

Ziaur Rahman
★★★★★

“Rare to find a garage you can truly trust. Fair price, brilliant service.”

Thinushan Keitheswaran
Read all reviews on Google ★★★★★
Chat on WhatsApp