Nissan Qashqai on the ramp for a clutch replacement at KITH Cars Garage & Bodyworks, Hackbridge

Clutch Replacement Mitcham: Eight Minutes to Our Workshop

Mitcham drivers are about eight minutes from our workshop, down Carshalton Road past Mitcham Junction. We fit complete OE-quality clutch kits, check the flywheel and hydraulics while the gearbox is out, and quote in writing first so you know the cost before we start.

  • ~8 min from Mitcham
  • Mon–Fri 8am–8pm · Sat 8am–5pm
Loading instant quote…

Mitcham's one-way loop and a clutch that bites too high

Since the Fair Green stretch of London Road became buses and cycles only, general traffic has to loop around the town centre one-way system. It is not a long detour, but it adds junctions and signals, and a car doing it daily clocks up plenty of pull-aways. Add the queues on the A217 London Road between Figges Marsh and the Cricket Green, and you have a clutch that works hard for its mileage.

The first thing most drivers notice is the bite point creeping up the pedal. A clutch that used to take up in the middle now engages right at the top, and pulling away from the lights near the Church of St Peter and St Paul needs more revs than it did. That is the friction plate wearing thin. Slip under load usually follows, first in fourth or fifth when you put your foot down on the faster A236 across Mitcham Common, then in the lower gears.

Many of the cars we see from Eastfields and the rest of Mitcham are hard-working hatchbacks, people carriers and older diesels, and quite a few also do private-hire or trade work. On those, we pay particular attention to the dual mass flywheel and the concentric slave cylinder, as both are common failure points at higher mileage. Where the car uses a concentric slave cylinder we replace it with the clutch, because reaching it later means taking the gearbox out again and paying for the same labour twice.

Getting to us is quick: follow the A217 to the Cricket Green, Cranmer Road to Carshalton Road, then over the bridge by Mitcham Junction and down London Road to Hackbridge. If the car has stopped selecting gears, we can collect it. You will have a written quote before we start and a 3-month workmanship warranty afterwards.

Clutch Replacement: what’s involved

The clutch connects the engine to the gearbox. A friction plate is clamped between the flywheel and a spring-loaded pressure plate. When you press the pedal, the release bearing pushes on the pressure plate springs and frees the plate so you can change gear. Most modern cars use a hydraulic system, and many have a concentric slave cylinder that combines the release bearing and slave cylinder inside the bellhousing.

Most diesels and many petrol cars also have a dual mass flywheel, which uses internal springs to absorb engine vibration. It wears alongside the clutch and is a common cause of judder and rattles. Because the gearbox has to come out to reach any of these parts, we inspect them all together so you only pay for the labour once.

From £735Written quote first
4–8 hoursTypical time in the workshop
3 monthsWorkmanship warranty

Signs your clutch needs replacing

Slipping under load

Engine revs rise but the car does not accelerate to match, most noticeable in a high gear going uphill or overtaking. This is a worn friction plate or oil contamination.

High bite point

As the friction plate wears, the clutch engages higher up the pedal travel. A bite point right at the top is a sign the plate is near the end of its life.

Judder when pulling away

Shaking as the clutch engages is often a worn dual mass flywheel, but can also be a contaminated plate or worn engine mounts. We check which before quoting.

Rattle at idle or a clunk when switching off

A metallic rattle at tickover or a knock as the engine stops are typical dual mass flywheel symptoms, caused by worn internal springs or excessive free play.

Noise when pressing the pedal

A whirr, chirp or grinding that appears or changes as you press the pedal usually points to a worn release bearing.

Difficulty selecting gears

Crunching into gear or struggling to get reverse with the engine running suggests the clutch is not fully releasing, often a hydraulic fault or a failing concentric slave cylinder.

Heavy, soft or sticking pedal

A pedal that sinks, stays down or feels spongy points to a leaking master or slave cylinder. A very heavy pedal can mean a worn pressure plate or a sticking cable.

Burning smell

A sharp smell after hill starts or heavy traffic is the friction material overheating. Occasional smells happen; regular ones mean the clutch is slipping.

When should a clutch be replaced?

A clutch has no fixed service interval. It is replaced when it slips, judders or stops releasing properly. Life depends heavily on driving style and use: a car that tows, carries heavy loads or spends its life in stop-start traffic will wear through a clutch far sooner than one used mostly on open roads. Riding the clutch and holding the car on the bite point on hills also shortens its life. If your car has a dual mass flywheel, it is often worn by the time the clutch needs replacing.

  • Typical clutch life: 60,000–100,000 miles, but under 40,000 in heavy town or towing use
  • Replace when slipping, a very high bite point or judder appears
  • Replace the dual mass flywheel if free play or rock is outside the manufacturer's limit
  • Replace the concentric slave cylinder with the clutch, as it needs the gearbox removed to reach
  • Fix any engine rear main seal or gearbox input seal leak at the same time

How we replace a clutch

  1. Check-in and road testWe drive the car to check the bite point, slip under load, judder and any noises, and confirm the fault is the clutch rather than engine mounts or the gearbox.
  2. Written quoteWe quote for the clutch kit and tell you in advance whether the dual mass flywheel is likely to need replacing, so there are no surprises.
  3. Gearbox removalThe engine is supported, then the driveshafts, linkages, starter and, on some cars, the subframe are removed to lower the gearbox.
  4. InspectionWe check the flywheel for heat marks, free play and rock, and look for oil leaks from the engine rear main seal or gearbox input shaft seal that would ruin a new clutch.
  5. Fit new clutchThe new friction plate is centred with an alignment tool, the pressure plate bolted down evenly to the correct torque, and the release bearing or concentric slave cylinder fitted.
  6. Refit gearboxThe gearbox goes back in with new fixings where the manufacturer requires them, and all linkages, driveshafts and mounts are refitted and torqued.
  7. Bleed and adjustThe hydraulic system is bled with fresh fluid and the pedal checked for full release and a correct bite point.
  8. Road test and handoverWe road test for smooth take-up, clean gear changes and no slip, then show you the old parts if you would like to see them.

Clutch parts we fit

We fit complete OE or OE-equivalent clutch kits from manufacturers such as LuK, Sachs, Valeo and Exedy, who supply clutches to car makers. A kit includes the friction plate, pressure plate and release bearing, or a concentric slave cylinder where your car uses one. If the dual mass flywheel needs replacing we fit a matching unit from the same quality of supplier rather than a cheap alternative, because the flywheel and clutch are designed to work together.

  • Friction plate and pressure plate
  • Release bearing or concentric slave cylinder
  • Dual mass or solid flywheel when required
  • Clutch hydraulic fluid to manufacturer specification
  • New flywheel bolts where specified by the manufacturer

How long it takes

4–8 hours

Most front-wheel drive cars take 4–6 hours. Four-wheel drive, some larger transverse engines and cars where the subframe must come out can take a full day or more, so we usually ask you to leave the car with us.

What’s included

  • Road test and diagnosis before quoting
  • Complete clutch kit fitted
  • Flywheel inspection and free play check
  • Check for rear main seal and input seal leaks
  • Hydraulic system bleed and final road test
  • 3-month workmanship warranty

From Mitcham to our Hackbridge workshop

From the town centre, follow the A217 London Road south to the Cricket Green, then take Cranmer Road (A239) to join Carshalton Road (A237) heading south. Carshalton Road crosses the railway and tram lines beside Mitcham Junction station and, past Beddington Corner, becomes London Road into Hackbridge, where Soho Mills is on London Road near Hackbridge station.

Take the A217 to the Cricket Green, then Cranmer Road onto Carshalton Road and over the railway at Mitcham Junction into Hackbridge, about 2.5 miles. If the clutch has failed completely, we can arrange recovery from Mitcham.

Directions from Mitcham

About Mitcham

Mitcham is a largely residential suburb in the east of Merton that grew from an old Surrey village famous for lavender growing, which still features on Merton Council's coat of arms. Its historic core is a string of village greens, from Fair Green and the clock tower in the town centre to the Cricket Green, with the wide open space of Mitcham Common to the south-east. Housing ranges from Victorian and interwar terraces to large council estates such as Phipps Bridge and Pollards Hill. Driving here means a mix of busy A-roads funnelling traffic between Tooting, Streatham, Morden and Croydon, and quiet residential side streets lined with parked cars.

Places nearby: Mitcham Common, Mitcham Cricket Green, Mitcham Clock Tower, Eagle House, The Canons, Church of St Peter and St Paul

Postcodes: CR4 · London Borough of Merton

More about KITH for Mitcham drivers

Clutch Replacement in Mitcham: your questions answered

My clutch pedal feels heavier than it used to. Is that wear?

It can be. As the friction plate wears, the pressure plate's diaphragm spring works at a different angle and the pedal often gets heavier. A sticking cable or a failing hydraulic part can do the same, so we check the release system along with the plate.

Can I keep driving to work while I wait for a booking?

If the clutch is only just starting to bite high, a short wait is usually fine. Once it slips under load it gets worse quickly and can overheat the flywheel, so book it in sooner. If it slips in first gear or reverse, it is best not to drive it.

Do you replace clutches on people carriers and seven-seaters?

Yes. Larger MPVs often take longer because of their size and engine layout, and some need the subframe lowered to get the gearbox out. We give you a realistic time along with the written quote.

Do I have to replace the dual mass flywheel as well?

Not always. We measure free play and rock against the manufacturer's limits once the gearbox is out. If it is within limits and not heat-damaged, it can be reused. If it is worn, fitting a new clutch against it usually brings the judder or rattle back.

What about solid flywheel conversion kits?

They are cheaper, but they remove the vibration damping the dual mass flywheel provides. Many owners notice more vibration and gearbox noise, especially at low revs. We generally recommend a like-for-like replacement and will explain the trade-off if you ask about a conversion.

Why is the concentric slave cylinder replaced with the clutch?

It sits inside the bellhousing, so the gearbox has to be removed to reach it. Slave cylinders commonly start leaking once disturbed or with age, and replacing it separately later would mean paying the same labour twice.

Can I make my clutch last longer?

Avoid resting your foot on the pedal, use the handbrake rather than the bite point on hills, and pull away with low revs. Selecting neutral at long stops also takes load off the release bearing.

Do you replace clutches on automatic or dual-clutch gearboxes?

Dual-clutch gearboxes such as DSG have their own clutch packs and are quoted individually after diagnosis. Conventional automatics use a torque converter rather than a clutch, and faults with those are handled through our gearbox services.

Price your clutch replacement now

Enter your reg and we’ll look up your car and price the job from our own labour rates and the book time for your model. Then book it in with a fixed written quote before any work starts.

  • Free, about 30 seconds, no sign-up
  • Parts, labour and VAT included
  • 3-month workmanship warranty
  • Collection from Mitcham can be arranged
“It’s rare to find a garage you can truly trust. Fair price, brilliant customer service.”Thinushan K. · ★★★★★ Google

Prefer to talk? Call 020 4629 9469 or WhatsApp us.

Chat on WhatsApp