Nissan Qashqai on the ramp for a clutch replacement at KITH Cars Garage & Bodyworks, Hackbridge

Clutch Replacement for Tooting, From Broadway to Tooting Bec

Tooting is around 18 minutes from our Hackbridge workshop, down Mitcham Road and through Mitcham. We replace clutches on the city cars, family cars and private-hire vehicles that work the A24, and we check the flywheel and hydraulics so the job is done once.

  • ~18 min from Tooting
  • Mon–Fri 8am–8pm · Sat 8am–5pm
Loading instant quote…

Up the hill from Tooting Broadway: where a worn clutch shows

Tooting sits on a slope, with Tooting Broadway at the bottom, Tooting Bec at the top and the A24 joining them. Upper Tooting Road and Tooting High Street form a red route with bus lanes, a 20mph limit on Upper Tooting Road and constant bus traffic, so the climb from the Broadway is made in first and second gear, stopping and starting at crossings. If your clutch is starting to slip, this is where it will tell you: the revs rise, the car hangs, and there is a smell of hot friction material by the time you reach Tooting Bec.

The Broadway junction itself, where the A24 meets the A217, is congested for much of the day. Add hospital traffic, visitors heading to Springfield University Hospital off Glenburnie Road, and drivers circling for a space in the controlled parking zones, and a lot of Tooting mileage is covered at walking pace. Around Tooting Bec Stadium and the Commons the roads open up, but you rarely stay on them long before the next junction.

Small hatchbacks and city cars suit the narrow terraced streets, but they do just as much stopping and starting as anything else, and a small car driven entirely in town can need a clutch surprisingly early. Private-hire cars and delivery vans on the A24 face the same problem at higher mileage. Whatever the car, we road test it, confirm it is the clutch rather than engine mounts or the gearbox, and give you a written quote that says whether the flywheel is likely to need replacing.

The drive to us runs along Mitcham Road past Tooting station, through Figges Marsh and round Mitcham to Carshalton Road, about five miles. With red routes and parking zones making it hard to leave a failing car anywhere, collection and delivery can be arranged, and recovery if it will not move. The work carries a 3-month workmanship warranty.

Clutch Replacement: what’s involved

The clutch connects the engine to the gearbox. A friction plate is clamped between the flywheel and a spring-loaded pressure plate. When you press the pedal, the release bearing pushes on the pressure plate springs and frees the plate so you can change gear. Most modern cars use a hydraulic system, and many have a concentric slave cylinder that combines the release bearing and slave cylinder inside the bellhousing.

Most diesels and many petrol cars also have a dual mass flywheel, which uses internal springs to absorb engine vibration. It wears alongside the clutch and is a common cause of judder and rattles. Because the gearbox has to come out to reach any of these parts, we inspect them all together so you only pay for the labour once.

From £735Written quote first
4–8 hoursTypical time in the workshop
3 monthsWorkmanship warranty

Signs your clutch needs replacing

Slipping under load

Engine revs rise but the car does not accelerate to match, most noticeable in a high gear going uphill or overtaking. This is a worn friction plate or oil contamination.

High bite point

As the friction plate wears, the clutch engages higher up the pedal travel. A bite point right at the top is a sign the plate is near the end of its life.

Judder when pulling away

Shaking as the clutch engages is often a worn dual mass flywheel, but can also be a contaminated plate or worn engine mounts. We check which before quoting.

Rattle at idle or a clunk when switching off

A metallic rattle at tickover or a knock as the engine stops are typical dual mass flywheel symptoms, caused by worn internal springs or excessive free play.

Noise when pressing the pedal

A whirr, chirp or grinding that appears or changes as you press the pedal usually points to a worn release bearing.

Difficulty selecting gears

Crunching into gear or struggling to get reverse with the engine running suggests the clutch is not fully releasing, often a hydraulic fault or a failing concentric slave cylinder.

Heavy, soft or sticking pedal

A pedal that sinks, stays down or feels spongy points to a leaking master or slave cylinder. A very heavy pedal can mean a worn pressure plate or a sticking cable.

Burning smell

A sharp smell after hill starts or heavy traffic is the friction material overheating. Occasional smells happen; regular ones mean the clutch is slipping.

When should a clutch be replaced?

A clutch has no fixed service interval. It is replaced when it slips, judders or stops releasing properly. Life depends heavily on driving style and use: a car that tows, carries heavy loads or spends its life in stop-start traffic will wear through a clutch far sooner than one used mostly on open roads. Riding the clutch and holding the car on the bite point on hills also shortens its life. If your car has a dual mass flywheel, it is often worn by the time the clutch needs replacing.

  • Typical clutch life: 60,000–100,000 miles, but under 40,000 in heavy town or towing use
  • Replace when slipping, a very high bite point or judder appears
  • Replace the dual mass flywheel if free play or rock is outside the manufacturer's limit
  • Replace the concentric slave cylinder with the clutch, as it needs the gearbox removed to reach
  • Fix any engine rear main seal or gearbox input seal leak at the same time

How we replace a clutch

  1. Check-in and road testWe drive the car to check the bite point, slip under load, judder and any noises, and confirm the fault is the clutch rather than engine mounts or the gearbox.
  2. Written quoteWe quote for the clutch kit and tell you in advance whether the dual mass flywheel is likely to need replacing, so there are no surprises.
  3. Gearbox removalThe engine is supported, then the driveshafts, linkages, starter and, on some cars, the subframe are removed to lower the gearbox.
  4. InspectionWe check the flywheel for heat marks, free play and rock, and look for oil leaks from the engine rear main seal or gearbox input shaft seal that would ruin a new clutch.
  5. Fit new clutchThe new friction plate is centred with an alignment tool, the pressure plate bolted down evenly to the correct torque, and the release bearing or concentric slave cylinder fitted.
  6. Refit gearboxThe gearbox goes back in with new fixings where the manufacturer requires them, and all linkages, driveshafts and mounts are refitted and torqued.
  7. Bleed and adjustThe hydraulic system is bled with fresh fluid and the pedal checked for full release and a correct bite point.
  8. Road test and handoverWe road test for smooth take-up, clean gear changes and no slip, then show you the old parts if you would like to see them.

Clutch parts we fit

We fit complete OE or OE-equivalent clutch kits from manufacturers such as LuK, Sachs, Valeo and Exedy, who supply clutches to car makers. A kit includes the friction plate, pressure plate and release bearing, or a concentric slave cylinder where your car uses one. If the dual mass flywheel needs replacing we fit a matching unit from the same quality of supplier rather than a cheap alternative, because the flywheel and clutch are designed to work together.

  • Friction plate and pressure plate
  • Release bearing or concentric slave cylinder
  • Dual mass or solid flywheel when required
  • Clutch hydraulic fluid to manufacturer specification
  • New flywheel bolts where specified by the manufacturer

How long it takes

4–8 hours

Most front-wheel drive cars take 4–6 hours. Four-wheel drive, some larger transverse engines and cars where the subframe must come out can take a full day or more, so we usually ask you to leave the car with us.

What’s included

  • Road test and diagnosis before quoting
  • Complete clutch kit fitted
  • Flywheel inspection and free play check
  • Check for rear main seal and input seal leaks
  • Hydraulic system bleed and final road test
  • 3-month workmanship warranty

From Tooting to our Hackbridge workshop

From Tooting Broadway take Mitcham Road (A217) east past Tooting station; it becomes London Road into Mitcham, through the signalised Figges Marsh junction and around the town centre one-way system to the Cricket Green. Take Cranmer Road (A239) to Carshalton Road (A237) and head south past Mitcham Junction; past Beddington Corner it becomes London Road into Hackbridge, where Soho Mills is near Hackbridge station.

Take Mitcham Road (A217) east from Tooting Broadway into Mitcham, through Figges Marsh to the Cricket Green, then Cranmer Road and Carshalton Road south to Hackbridge, about 18 minutes. If the car will not drive, we can arrange recovery from Tooting.

Directions from Tooting

About Tooting

Tooting is a lively, densely built district of south-west London centred on Tooting Broadway and Tooting Bec, two Northern line stations at the bottom and top of the hill. Its streets are mostly Victorian and Edwardian terraces, including the Totterdown Fields estate, the first London County Council cottage estate, with larger houses towards Tooting Bec Common and Furzedown. It has a celebrated food scene along Upper Tooting Road and two indoor markets, and a big workforce at St George's Hospital. Driving is busy and slow on the main roads, with narrow, heavily parked side streets.

Places nearby: St George's Hospital, Tooting Bec Lido, Tooting Commons, Granada Tooting, Broadway Market, Tooting Market

Postcodes: SW17 · London Borough of Wandsworth

More about KITH for Tooting drivers

Clutch Replacement in Tooting: your questions answered

Where can I leave a car with a failing clutch in Tooting while I wait for a booking?

Ideally not on the street, as the controlled parking zones around Tooting Broadway run Monday to Saturday and a car that will not move can soon attract a ticket. Book it in and we can collect it, or arrange recovery if it cannot be driven.

Is it the clutch or the gearbox making a noise when I pull away?

A noise that appears or changes when you press the pedal usually comes from the release bearing, which is part of the clutch. A noise that goes away when you press the pedal often points to a gearbox input shaft bearing, and one that changes with road speed is more likely a wheel bearing or driveshaft. We diagnose it before quoting.

Can you do a clutch on a Saturday?

We are open Monday to Friday 8am to 8pm and Saturday 8am to 5pm, so Saturday bookings are possible. A clutch typically takes four to eight hours depending on the car, so an early drop-off gives the best chance of same-day collection.

Do I have to replace the dual mass flywheel as well?

Not always. We measure free play and rock against the manufacturer's limits once the gearbox is out. If it is within limits and not heat-damaged, it can be reused. If it is worn, fitting a new clutch against it usually brings the judder or rattle back.

What about solid flywheel conversion kits?

They are cheaper, but they remove the vibration damping the dual mass flywheel provides. Many owners notice more vibration and gearbox noise, especially at low revs. We generally recommend a like-for-like replacement and will explain the trade-off if you ask about a conversion.

Why is the concentric slave cylinder replaced with the clutch?

It sits inside the bellhousing, so the gearbox has to be removed to reach it. Slave cylinders commonly start leaking once disturbed or with age, and replacing it separately later would mean paying the same labour twice.

Can I make my clutch last longer?

Avoid resting your foot on the pedal, use the handbrake rather than the bite point on hills, and pull away with low revs. Selecting neutral at long stops also takes load off the release bearing.

Do you replace clutches on automatic or dual-clutch gearboxes?

Dual-clutch gearboxes such as DSG have their own clutch packs and are quoted individually after diagnosis. Conventional automatics use a torque converter rather than a clutch, and faults with those are handled through our gearbox services.

Price your clutch replacement now

Enter your reg and we’ll look up your car and price the job from our own labour rates and the book time for your model. Then book it in with a fixed written quote before any work starts.

  • Free, about 30 seconds, no sign-up
  • Parts, labour and VAT included
  • 3-month workmanship warranty
  • Collection from Tooting can be arranged
“It’s rare to find a garage you can truly trust. Fair price, brilliant customer service.”Thinushan K. · ★★★★★ Google

Prefer to talk? Call 020 4629 9469 or WhatsApp us.

Chat on WhatsApp