Wheel Alignment at our own workshop on London Road, Hackbridge SM6. Put your registration in and we will have the right sizes on the shelf before you arrive rather than ordering them while you wait.
Sutton Council’s own ward parking survey for Wandle ward, which covers Hackbridge, found 67 per cent of residents reporting a
parking problem on their street, 39 per cent parking on the road and nearly nine in ten households
with at least one car. The Edwardian streets off London Road were laid out before any of that,
and the result is parking spaces that are exactly as long as a car and no longer.
Tyres and wheels pay for it. Kerbing a sidewall while reversing into a tight gap is the single
commonest thing we see on local cars, and a kerbed sidewall is not a cosmetic matter: the cords
inside it are what hold the tyre together and a scuff deep enough to show them is a tyre that
needs replacing rather than watching.
The alignment goes the same way. A kerb hard enough to mark an alloy is usually hard enough to
move the tracking, and once the tracking is out the tyre wears across its width instead of evenly.
People replace a worn tyre, do not check why it wore, and replace the next one early too.
Which is why on anything that has been kerbed we would rather look at the geometry than just
sell a tyre. The tyre is the symptom.
Before you come down
Put your registration in above. It gives us your sizes so the tyres are
here rather than on order while you sit in reception.
Check all four, not just the bad one. Tyres age as well as wear, and a set
bought together tends to need replacing together.
Mention any kerb strike. It changes whether this is a tyre job or an
alignment job, and the alignment is what stops you buying another tyre early.
Look at the inner edges. Wear you cannot see from outside the car is the
wear that tells you the geometry is out.
We will tell you if a tyre has life left in it. Selling four when you needed two is the
quickest way to never see somebody again in a suburb this size.
Mechanical
Wheel Alignment: what’s involved
Wheel alignment describes the angles at which the wheels sit in relation to each other and to the road. Toe is whether a pair of wheels points inwards or outwards seen from above, the angle that most affects tyre wear. Camber is the inward or outward lean of the wheel seen from the front, and it decides how flat the tread sits under cornering load. Caster is the backward tilt of the steering axis seen from the side, which gives the steering its self-centring and straight-line stability.
On a four-wheel measurement the rear axle is read as well. The thrust angle is the direction the rear axle actually points relative to the car's centreline, and if it is out the car tracks slightly sideways with the steering wheel crooked even when front toe is perfect. Setting the front wheels to the thrust line rather than to the geometric centre is what puts the wheel straight and keeps it there. Manufacturers publish a target for each angle with a tolerance either side, and those are the figures we work to.
From £59Written quote first
60–90 minutesTypical time in the workshop
3 monthsWorkmanship warranty
Signs your alignment needs checking
Steering wheel sits crooked
The car goes straight but the spokes are at an angle. That is usually front toe set on the wrong reference, or a rear thrust angle that has never been measured.
Pulling to one side
On a flat, level road with a light grip the car drifts left or right. Unequal camber or caster is a common cause, though a dragging brake or a faulty tyre can do the same and has to be ruled out.
Feathered tread blocks
Run your palm across the tread: if the blocks feel sharp in one direction and smooth in the other, the toe setting is scrubbing the tyre sideways as it rolls.
One shoulder worn away
The inner or outer edge is down to the wear bars while the rest of the tread looks healthy. That pattern points to a camber or toe error rather than pressures.
Scrubbing or squeal on slow turns
A rubbing noise from the front when manoeuvring at walking pace can mean the wheels are fighting each other through the turn.
After a kerb strike or pothole
A hard hit can shift a track rod, bend a steering arm or move a subframe. The car may still feel normal while the tyre quietly wears out.
Steering slow to straighten
Coming out of a roundabout the wheel does not want to return on its own. Reduced caster or a binding top mount will both do this.
New tyres wearing quickly
If a fresh set loses noticeable tread within a few thousand miles, the geometry is almost always the reason rather than the tyres.
When should alignment be checked?
Have the angles checked whenever the suspension or steering has been disturbed, which means after replacing shock absorbers, springs, control arms, track rod ends or a steering rack, and after any accident repair involving the front end. A solid kerb impact or a deep pothole is worth a check even if nothing feels different. Beyond that, a check once a year, or with every new set of tyres, catches slow drift caused by settling springs and ageing bushes before it costs you rubber.
After any steering or suspension component is replaced
After a kerb strike, pothole impact or front-end accident repair
Once a year, or roughly every 10,000–12,000 miles
When fitting a new set of tyres, if the old ones wore unevenly
After lowering springs or a coilover kit are fitted
How we align a car
Road test and check-inWe drive the car to feel where it pulls and where the steering wheel sits, and we ask what you have noticed. Any recent impact or repair work is noted.
Wear and pressure checkThe car goes on the ramp and we check for play in the track rod ends, ball joints, wheel bearings and bushes, and look for damaged or mismatched tyres. Anything loose is quoted first, because an angle set on a worn joint will not stay set.
Set up on the alignment gearTargets are clamped to all four wheels and the car is rolled through a compensation routine so the equipment ignores any small buckle in a rim.
Measure and recordWe take the readings for toe, camber, caster and thrust angle, compare them with the manufacturer's data for your registration and print the starting figures.
Explain what is adjustableWe show you which angles are out and which of them your car actually allows us to move. Where a correction needs an eccentric bolt kit or a camber bolt, we quote it before fitting anything.
Adjust to specificationLock nuts are released, seized threads are freed with heat and penetrant where needed, and each adjustable angle is brought into tolerance with the steering rack held centred.
Centre and tightenThe steering wheel is set straight with the rack in the middle of its travel, then every lock nut and clamp is torqued and the gaiters checked for twist.
Reset and retestOn cars with stability control we carry out a steering angle sensor reset, then re-measure and print the finished figures.
Road test and handoverA second drive confirms the car tracks straight and the wheel sits level. You keep the before and after printout.
Parts and adjusters
Most alignments need no parts at all, only time and careful adjustment. Where a thread has corroded solid, or a gaiter tears as the track rod turns, we quote the replacement before going further. Some cars need an adjuster kit to bring camber back into range, and we use OE or OE-equivalent components from established suspension suppliers such as Febi or Lemförder rather than unbranded parts.
Track rod ends and inner rack ends where threads are seized or worn
Steering rack gaiters and clips
Eccentric camber bolts and adjuster kits where the design allows
New lock nuts and clamp bolts
Subframe alignment where bolts have been disturbed
How long it takes
60–90 minutes
A four-wheel measurement and adjustment usually takes an hour to an hour and a half. Corroded adjusters, cars with rear toe and camber to set, and anything needing a parts change will take longer. Most jobs are done while you wait or over a morning.
What’s included
Pre-alignment inspection of steering and suspension joints
Tyre pressures set to the placard before measuring
Four-wheel measurement of toe, camber, caster and thrust angle
Adjustment of every angle the vehicle allows to be adjusted
Steering wheel centred and fixings torqued
Printed before and after readings to keep
Finding us
We are on London Road, which is the point
There is no journey to describe. We are at Unit 1 Soho Mills on London Road, which is the road
you are already on — a couple of minutes from the station, the parade and the level
crossing, and inside the SM6 postcode rather than a drive away from it.
That changes how you can use us, and it is worth saying plainly:
You can walk in. If something is making a noise, bring it down and we will
look at it rather than booking you in for a week on Thursday to hear a description of it.
You can leave the car and walk home. Most of Hackbridge is ten minutes on
foot from the yard, which removes the whole business of arranging a lift or waiting in a
reception.
You can get to the station from us. If the car has to stay in, you are a few
minutes from the platform rather than stranded.
We can look at it before quoting. Where a job needs the car on a ramp to
price honestly, being local means that is a short detour rather than a second trip across
town.
Being the workshop in the place rather than the workshop near it is most of why people use us.
It is also why we would rather tell you something is not worth repairing than take the work —
we are going to see you in the Co-op.
Wheel Alignment in Hackbridge: your questions answered
I kerbed it reversing into a space. Is the tyre still safe?
If the scuff is deep enough to show the cords in the sidewall, no. A sidewall is not repairable and the cords are what hold the tyre together. Bring it down and we will look.
Do I need the alignment doing as well?
If the kerb was hard enough to mark the wheel, usually yes. Tracking knocked out by a kerb wears the new tyre unevenly and you end up buying another one early.
Can you do all four while I wait?
Usually, if we know you are coming. Put your registration in above so we have the right sizes on the shelf rather than ordering them while you sit there.
Where exactly are you in Hackbridge?
Unit 1 Soho Mills, London Road, SM6 7HN — a couple of minutes from Hackbridge station and the parade. There is room to leave a car with us.
Can I just turn up?
For a look at something, yes. For work that needs a ramp and a slot, call or put your registration into the box on this page first so we can give you a time rather than keep you waiting.
Instant quote
Price your wheel alignment now
Enter your reg and we’ll look up your car and price the job from our own labour rates and the book time for your model. Then book it in with a fixed written quote before any work starts.
Free, about 30 seconds, no sign-up
Parts, labour and VAT included
3-month workmanship warranty
Collection from Hackbridge can be arranged
“It’s rare to find a garage you can truly trust. Fair price, brilliant customer service.”Thinushan K. · ★★★★★ Google