Alloy Wheel Refurbishment at our own workshop on London Road, Hackbridge SM6. Put your registration in and we will have the right sizes on the shelf before you arrive rather than ordering them while you wait.
Sutton Council’s own ward parking survey for Wandle ward, which covers Hackbridge, found 67 per cent of residents reporting a
parking problem on their street, 39 per cent parking on the road and nearly nine in ten households
with at least one car. The Edwardian streets off London Road were laid out before any of that,
and the result is parking spaces that are exactly as long as a car and no longer.
Tyres and wheels pay for it. Kerbing a sidewall while reversing into a tight gap is the single
commonest thing we see on local cars, and a kerbed sidewall is not a cosmetic matter: the cords
inside it are what hold the tyre together and a scuff deep enough to show them is a tyre that
needs replacing rather than watching.
The alignment goes the same way. A kerb hard enough to mark an alloy is usually hard enough to
move the tracking, and once the tracking is out the tyre wears across its width instead of evenly.
People replace a worn tyre, do not check why it wore, and replace the next one early too.
Which is why on anything that has been kerbed we would rather look at the geometry than just
sell a tyre. The tyre is the symptom.
Before you come down
Put your registration in above. It gives us your sizes so the tyres are
here rather than on order while you sit in reception.
Check all four, not just the bad one. Tyres age as well as wear, and a set
bought together tends to need replacing together.
Mention any kerb strike. It changes whether this is a tyre job or an
alignment job, and the alignment is what stops you buying another tyre early.
Look at the inner edges. Wear you cannot see from outside the car is the
wear that tells you the geometry is out.
We will tell you if a tyre has life left in it. Selling four when you needed two is the
quickest way to never see somebody again in a suburb this size.
Bodywork
Alloy Wheel Refurbishment: what’s involved
Most alloy wheels have one of two finishes. Painted or powder coated wheels have a solid colour coating, usually silver, grey, black or gunmetal, over the whole wheel. Diamond cut wheels have a bright, finely machined face produced on a lathe and sealed with clear lacquer, often with painted sections between the spokes. They look different and are repaired differently, so the first step is identifying which you have.
Powder coating is a full refurbishment: the wheel is stripped and repaired, then the powder is applied electrostatically and cured in an oven, giving a thick, tough finish in almost any colour. Diamond cutting machines a very thin layer from the face and re-lacquers it; because it removes metal, a wheel can only be re-cut a limited number of times. Wheels that are cracked or badly buckled are checked for safety first, and sometimes need replacing rather than refurbishing.
From £105 per wheelWritten quote first
Same day – 3 daysTypical time in the workshop
3 monthsWorkmanship warranty
Signs your alloys need refurbishing
Kerb rash
Scuffs and gouges on the rim edge from parking. Once through the coating, corrosion can start underneath.
White patches under the lacquer
Milky corrosion creeping under the clear lacquer is common on diamond cut wheels and spreads over time.
Flaking or bubbling paint
Corrosion under the coating, often starting at the rim edge, around the spokes or at the wheel bolt holes.
Slow puncture with no obvious cause
Corrosion on the bead seat, where the tyre seals against the rim, can let air escape slowly.
Dull or stained finish
Brake dust baked on over time, or damage from harsh acidic wheel cleaners.
Vibration at speed
Can point to a buckled wheel or balance problem. We check the wheel runs true before refurbishing it.
Visible crack
A crack in the rim or spoke is a safety issue, not a cosmetic one, and needs assessment before anything else.
When should it be done?
Refurbish wheels once the finish has been broken, not just when they look bad. Kerb damage and chips let water and road salt reach the aluminium, and corrosion then creeps under the surrounding paint or lacquer, which is why diamond cut wheels often develop spreading white patches. Wheels losing air slowly through the bead should be done promptly. Many owners refurbish all four together so they match, or have it done before selling or returning a lease car.
Kerb rash that has broken through the paint or lacquer
White or milky corrosion spreading under diamond cut lacquer
Tyres slowly losing pressure through corroded bead seats
When fitting new tyres, as the tyres are coming off anyway
Before a sale or lease return
How we refurbish alloy wheels
Inspect and identifyWe identify the finish, assess the damage and check each wheel for cracks and buckles, then quote per wheel.
Remove tyres and weightsTyres and balance weights are removed, and tyre pressure monitoring sensors are taken out and kept safe.
Strip or prepareFor a full refurbishment the old coating is stripped; for a cosmetic repair the damaged area is sanded back.
Repair the damageKerb damage is filled and shaped, corrosion is removed and the bead seats are cleaned so the tyre seals properly.
Apply the finishPowder coat is applied and cured in an oven, or paint is applied and cured. For diamond cut wheels, the face is machined on a lathe after the colour coat, then sealed with clear lacquer.
Refit tyres and balanceTyres are refitted with new valves where needed and each wheel is balanced with new weights.
Refit and hand overWheels are refitted and tightened to the manufacturer's torque setting. We recommend a torque check after about 50 miles.
Finishes and materials
Powder coat gives the most durable finish and comes in a wide range of colours. Diamond cut wheels are machined and sealed with clear lacquer to protect the bare aluminium, and painted sections are matched to the original finish as closely as possible. New valves are fitted where needed, and wheels are balanced with new weights before they go back on the car.
Powder coat primer and colour coat
Clear lacquer for diamond cut faces
Wheel paint matched to the original for cosmetic repairs
New tyre valves where required
New balance weights
How long it takes
Same day – 3 days
A cosmetic kerb rash repair on one or two wheels can often be done in a day. A full powder coat or diamond cut refurbishment of a set usually takes 2–3 days, as the wheels need stripping, coating and curing. Tell us when you book if you need the car back by a particular day.
What’s included
Inspection for cracks and buckles before work starts
Tyre removal and refitting
Repair and refinishing of the wheel
Balancing with new weights
Refitting and torquing to the correct setting
12-month workmanship warranty
Finding us
We are on London Road, which is the point
There is no journey to describe. We are at Unit 1 Soho Mills on London Road, which is the road
you are already on — a couple of minutes from the station, the parade and the level
crossing, and inside the SM6 postcode rather than a drive away from it.
That changes how you can use us, and it is worth saying plainly:
You can walk in. If something is making a noise, bring it down and we will
look at it rather than booking you in for a week on Thursday to hear a description of it.
You can leave the car and walk home. Most of Hackbridge is ten minutes on
foot from the yard, which removes the whole business of arranging a lift or waiting in a
reception.
You can get to the station from us. If the car has to stay in, you are a few
minutes from the platform rather than stranded.
We can look at it before quoting. Where a job needs the car on a ramp to
price honestly, being local means that is a short detour rather than a second trip across
town.
Being the workshop in the place rather than the workshop near it is most of why people use us.
It is also why we would rather tell you something is not worth repairing than take the work —
we are going to see you in the Co-op.
Alloy Wheel Refurbishment in Hackbridge: your questions answered
I kerbed it reversing into a space. Is the tyre still safe?
If the scuff is deep enough to show the cords in the sidewall, no. A sidewall is not repairable and the cords are what hold the tyre together. Bring it down and we will look.
Do I need the alignment doing as well?
If the kerb was hard enough to mark the wheel, usually yes. Tracking knocked out by a kerb wears the new tyre unevenly and you end up buying another one early.
Can you do all four while I wait?
Usually, if we know you are coming. Put your registration in above so we have the right sizes on the shelf rather than ordering them while you sit there.
Where exactly are you in Hackbridge?
Unit 1 Soho Mills, London Road, SM6 7HN — a couple of minutes from Hackbridge station and the parade. There is room to leave a car with us.
Can I just turn up?
For a look at something, yes. For work that needs a ramp and a slot, call or put your registration into the box on this page first so we can give you a time rather than keep you waiting.
Instant quote
Price your alloy wheel refurbishment now
Enter your reg and we’ll look up your car and price the job from our own labour rates and the book time for your model. Then book it in with a fixed written quote before any work starts.
Free, about 30 seconds, no sign-up
Parts, labour and VAT included
12-month workmanship warranty
Collection from Hackbridge can be arranged
“It’s rare to find a garage you can truly trust. Fair price, brilliant customer service.”Thinushan K. · ★★★★★ Google
The damage that comes to us from a hundred yards away is overwhelmingly low-speed. Parked-car
damage, in a suburb where 67 per cent of residents told the council their street has a parking
problem and 39 per cent park on it.
Bumper corners and scuffed ends. Reversing into a gap on an Edwardian street
that was laid out before anyone owned a car.
Door edge dings and creased doors. Cars parked close enough on both sides
that there is no safe arc to open into.
Mirror casings. Taken off by a passing van on a road narrowed to one lane by
parking.
Kerbed alloys. The commonest thing on the list, and the one most people put
off longest.
Scrapes down one side. Usually a squeeze past something double-parked or a
delivery lorry at the parade.
What we see far less of is the high-speed structural damage that comes off the A217 and the
A232. Hackbridge sits off the main network rather than on it, which is good news for the severity
of what happens here and no help at all to the state of the paint.