Citroën in for a wheel bearing replacement at KITH Cars Garage & Bodyworks, Hackbridge

Wheel Bearing Replacement for Tooting Drivers, Collection Available

Around Tooting Broadway, 20mph limits and red-route traffic mean a worn wheel bearing can be almost silent until you leave the area. We are about 18 minutes away in Hackbridge, and we can collect your car if parking or shift work makes a drop-off difficult.

  • ~18 min from Tooting
  • Mon–Fri 8am–8pm · Sat 8am–5pm
Loading instant quote…

Shift work, delivery vans and bearing noise in Tooting

Tooting runs around the clock. Staff at Springfield University Hospital and St George's work shifts, delivery vans keep the shops on Upper Tooting Road and Tooting High Street stocked, and private hire drivers work the Broadway late into the evening. Vehicles in constant use cover mileage quickly, and wheel bearings, which carry the vehicle's weight on every one of those miles, eventually wear. Vans that run loaded are affected most at the rear. Hospital staff cars parked for long shifts and then driven home also make many short trips.

The roads do not help you hear it. The A24 is a 20mph red route with bus lanes, Wandsworth has 20mph on its residential streets, and traffic noise around the Broadway is constant. A bearing hum that would be obvious at 40mph is easily lost at 20. Heading out past Tooting Bec Stadium towards Streatham, or east along Mitcham Road on the way to us, is often when drivers finally hear it, usually as a drone that rises and falls with speed.

We diagnose with a road test, weaving to load each side, and a lift check for play and roughness. For vans we look at both sides of the loaded axle. The written quote tells you which bearing type your vehicle uses and how long the job will take, so you can plan around shifts. After fitting, we check the ABS encoder faces the sensor, read the fault codes and road test to confirm the noise has gone. If a van needs to be back on the road quickly, tell us and we will check parts availability before it arrives.

Mitcham Road takes you east from Tooting Broadway into Mitcham, then through the Figges Marsh junction and town centre to the Cricket Green, Cranmer Road and Carshalton Road south to Hackbridge, about 18 minutes. With loading and parking so restricted around the Broadway, collection and delivery can be arranged. Our labour is covered by a 3-month workmanship warranty.

Wheel Bearing Replacement: what’s involved

Each wheel turns on a sealed bearing packed with grease, which supports the car's full weight and every cornering and braking load. On many modern cars the bearing is part of a bolt-on hub unit, while others use a separate bearing pressed into the hub carrier. Most also carry the ABS sensor's magnetic encoder ring in the bearing seal, so the bearing is part of the braking system's electronics as well.

Bearings wear out when the seal lets in water and grit, or when they are damaged by pothole or kerb impacts. The first sign is usually a hum or drone that rises with speed and is easy to mistake for tyre noise. As wear increases, play develops in the wheel. Replacing a bearing early is a straightforward job; leaving it can damage the hub, affect the ABS and, in extreme cases, let the wheel move on the hub.

From £235Written quote first
1–3 hoursTypical time in the workshop
3 monthsWorkmanship warranty

Signs of a worn wheel bearing

Hum or drone rising with speed

The classic sign is a low roar that gets louder as speed increases, often most noticeable from around 30 mph upwards.

Noise changes when weaving

A worn bearing gets louder when it is loaded. Turning right puts weight on the left wheels, so a noise that grows when turning right usually points to a left-hand bearing, and the other way round.

Grinding or rumbling

As wear advances, the hum becomes a grinding or rumbling that you may feel through the floor or steering.

Play in the wheel

Rocking the wheel at the top and bottom with the car raised reveals movement if the bearing is badly worn.

ABS or traction warning light

On bearings with a built-in encoder ring, a damaged seal or excessive play can upset the ABS signal and trigger a warning light.

Vibration through the steering

A worn front bearing can cause vibration or looseness in the steering, especially when cornering.

Uneven brake pad wear

Play in the bearing can knock the pads back and cause uneven wear or a longer pedal on one side.

When should a wheel bearing be replaced?

Wheel bearings do not have a service interval; they are replaced when they become noisy or develop play. Many last well over 100,000 miles, but a heavy pothole or kerb strike can damage one much sooner. Because bearing noise builds gradually and sounds like tyre roar, it is easy to get used to it. If you notice a new drone at speed, especially one that changes as you steer, have it checked so it can be replaced before it wears further.

  • Replace when noisy, when play is found or when an ABS fault is traced to the bearing
  • Check after a heavy pothole or kerb impact
  • Many bearings last 80,000–150,000 miles, but it varies with roads and loads
  • Replace in pairs only if both sides are worn; a good bearing does not need changing
  • Check before an MOT if you hear a drone at speed

How we replace a wheel bearing

  1. Check-in and road testWe drive the car at varying speeds and weave gently to load each side, narrowing down which bearing is making the noise.
  2. Lift and checkWith the car raised we check each wheel for play and spin it by hand to feel roughness. Where needed we use a chassis listening device to confirm the corner.
  3. Written quoteWe confirm whether your car uses a bolt-on hub unit or a pressed bearing and quote in writing.
  4. Strip the cornerThe wheel, brake calliper, disc and ABS sensor are removed, and the driveshaft is released on driven wheels.
  5. Replace the bearingHub units are unbolted and replaced. Pressed bearings are removed and fitted using a press, pushing only on the correct race so the new bearing is not damaged.
  6. Check the ABS encoderWhere the encoder ring is in the bearing seal, we make sure it faces the ABS sensor. Fitted the wrong way round, the ABS will not work correctly.
  7. Torque the hub nutThe hub nut is tightened to the manufacturer's torque, and replaced if it is a single-use nut.
  8. Road test and handoverWe refit the brakes, check for ABS fault codes, road test to confirm the noise has gone and explain what we found.

Wheel bearing parts we fit

We fit OE or OE-equivalent wheel bearings and hub units from bearing manufacturers such as SKF, FAG, SNR and Timken, which supply car makers directly. Quality really matters here: cheaper bearings are known to become noisy again quickly. Bearing kits usually come with a new hub nut and circlips where required, and we replace single-use fixings rather than reusing them.

  • Wheel bearing or complete hub bearing unit
  • New hub nut and circlips where supplied or specified
  • ABS encoder ring integrated in the bearing seal where applicable
  • New fixings where the manufacturer specifies single-use bolts

How long it takes

1–3 hours

A bolt-on hub unit usually takes 1–1.5 hours per side. A pressed bearing takes longer, typically 2–3 hours, especially if fixings are corroded. Most jobs are done the same day.

What’s included

  • Road test and wheel bearing diagnosis
  • Bearing or hub unit fitted with correct tools
  • Hub nut tightened to manufacturer torque
  • ABS encoder orientation check and fault code check
  • Road test after fitting
  • 3-month workmanship warranty

From Tooting to our Hackbridge workshop

From Tooting Broadway take Mitcham Road (A217) east past Tooting station; it becomes London Road into Mitcham, through the signalised Figges Marsh junction and around the town centre one-way system to the Cricket Green. Take Cranmer Road (A239) to Carshalton Road (A237) and head south past Mitcham Junction; past Beddington Corner it becomes London Road into Hackbridge, where Soho Mills is near Hackbridge station.

Take Mitcham Road (A217) east through Mitcham to the Cricket Green, then Cranmer Road and Carshalton Road (A237) south to Hackbridge, about 18 minutes and 5 miles. Collection and delivery can be arranged.

Directions from Tooting

About Tooting

Tooting is a lively, densely built district of south-west London centred on Tooting Broadway and Tooting Bec, two Northern line stations at the bottom and top of the hill. Its streets are mostly Victorian and Edwardian terraces, including the Totterdown Fields estate, the first London County Council cottage estate, with larger houses towards Tooting Bec Common and Furzedown. It has a celebrated food scene along Upper Tooting Road and two indoor markets, and a big workforce at St George's Hospital. Driving is busy and slow on the main roads, with narrow, heavily parked side streets.

Places nearby: St George's Hospital, Tooting Bec Lido, Tooting Commons, Granada Tooting, Broadway Market, Tooting Market

Postcodes: SW17 · London Borough of Wandsworth

More about KITH for Tooting drivers

Wheel Bearing Replacement in Tooting: your questions answered

Can you work around my hospital shift pattern?

We are open Monday to Friday 8am to 8pm and Saturday 8am to 5pm, and collection and delivery can be arranged locally. Tell us your shift times when you book and we will plan the work so the car is back when you need it.

Do you replace wheel bearings on delivery vans?

Yes, on light commercial vans as well as cars. Loaded vans put extra weight on their rear bearings, so we check both sides of the axle and fit bearings of the correct specification for the van.

Why do I only hear the noise on the way out of Tooting?

Bearing noise grows with speed, so on 20mph roads with heavy traffic it can be almost inaudible. On a faster road it becomes clearer. A noise that appears only above around 30mph and changes when you steer strongly suggests a bearing, which we then confirm on the lift.

How do I know it is a wheel bearing and not my tyres?

Both can hum at speed. Tyre noise usually changes with the road surface and sounds much the same when turning, while bearing noise tends to get louder when you steer one way and quieter the other. A road test and lift check confirm it.

Should both wheel bearings on an axle be replaced?

Only if both are worn. Unlike brakes, bearings do not need replacing in pairs for balance. We check both sides and tell you if the other is starting to go.

Can a wheel bearing cause an ABS warning light?

Yes. Many bearings carry the magnetic ring the ABS sensor reads. A damaged seal, excessive play or a bearing fitted the wrong way round can cause ABS and traction control faults.

Is a clicking noise on full lock a wheel bearing?

Usually not. Rhythmic clicking when turning sharply under power is more often a worn outer CV joint on the driveshaft. We check both during diagnosis.

Is it safe to drive with a noisy wheel bearing?

A light hum is not an immediate danger, but it will get worse and can damage surrounding parts. If the noise is loud, grinding or you can feel play in the steering, book in soon and avoid long motorway journeys.

Price your wheel bearing replacement now

Enter your reg and we’ll look up your car and price the job from our own labour rates and the book time for your model. Then book it in with a fixed written quote before any work starts.

  • Free, about 30 seconds, no sign-up
  • Parts, labour and VAT included
  • 3-month workmanship warranty
  • Collection from Tooting can be arranged
“It’s rare to find a garage you can truly trust. Fair price, brilliant customer service.”Thinushan K. · ★★★★★ Google

Prefer to talk? Call 020 4629 9469 or WhatsApp us.

Chat on WhatsApp